Instructions for Model RP-SK81
DISH
®
1000 Replacement
Back-up and Feed Arm Assembly
For help, email [email protected] or call 1-800-788-4417
www.winegard.com/mobile
Automatic Multi-Satellite TV Antenna
Winegard and TRAV’LER are registered trademarks of Winegard Company.
DIRECTV is a registered trademark of DIRECTV, LLC.
DISH is a registered trademark of Dish Network L.L.C.
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601
800-288-8094 • Fax 319-754-0787 • www.winegard.com
Printed in U.S.A. ©2013 Winegard Company Rev1 3-16 2452311
1
2
3
4
1
2
3
4
Reflector bracket
1
2
3
4
Adapter plate
Screws removed
from wider end of
integrated adapter
LNB slid out from
integrated adapter
Integrated
adapter
1. Press and hold “POWER” for two seconds to turn on the
interface box. Wait until the interface box finishes “connecting
to antenna.” The antenna may enter the search routine after ten
seconds. Pay attention to the pinch points as the antenna raises!
2. Wait until the antenna has at least raised to a position
in which the LNB arm is parallel to the roof. Then, press
“POWER” and “SELECT” at the same time. The antenna
should stop moving.
3. Unplug the interface box.
4. Remove the four reflector nuts and bolts with a
7
/
16
″
wrench,
and remove the reflector. Set the reflector, nuts, and bolts
aside; you will need these later.
5. Remove and set aside the four nuts and bolts holding the LNB
guard to the feed arm. Then, slide the LNB guard down the
feed arm and toward the reflector.
6. Remove and set aside the
two screws from the wider
end of the underside of the
integrated adapter.
7. Carefully slide the LNB out
from the integrated adapter.
Disconnect the three coax
cables from the LNB
using a
7
/
16
″
wrench,
and set aside the LNB.
8. Remove the two screws from the narrower end of the
integrated adapter, and gently pull apart the integrated adapter.
9. After removing the integrated adapter from the feed arm,
remove the LNB guard from the feed arm.
10. Using a ½
″
wrench, remove and set aside the four bolts from
the reflector bracket, and remove the feed arm assembly.
11. Align the four holes on the inside of the reflector bracket with the
four marked holes in the adapter plate. See marked holes below.
12. Install bolts through the four
aligned holes in the adapter plate
and reflector bracket, and tighten.
Note: the reflector bracket
should be positioned with
the feed arm assembly at the
bottom of the adapter plate
(near the third hole).
13. Slide the LNB guard onto the feed arm.
14. Position the integrated adapter on the feed arm. Make sure
that the two posts on the bottom of the integrated adapter
have been inserted into the two holes in the feed arm. The
integrated adapter should slant upwards.
15. Insert the two screws (removed earlier) through the holes in
the bottom of the integrated adapter and feed arm. Thread a
nut onto each bolt, and tighten.
16. Run the sheathed cable through the feed arm.
17. Connect the cables running through the feed arm to ports 1–3
(in any order) on the LNB. Tighten each cable until fingertight,
and then use a
7
/
16
″
wrench to tighten a quarter turn more. Do
not overtighten.
18. Slide the LNB into the integrated adapter, and re-install the
two screws (removed earlier) through the wider end of the
underside of the integrated adapter. Tighten.
19. Slide the LNB guard up the feed arm and over the LNB. The
front of the LNB guard should be ~½
″
in front of the LNB and
should not be touching the LNB. Install the four bolts through
the four holes in the LNB guard. Thread a nut onto each bolt,
and tighten.
20. Install the reflector bolts through the four corresponding holes
in the reflector and reflector bracket. Install the reflector nuts,
and tighten.
21. Plug in the interface box.
22. Press and hold “POWER” for two seconds to turn on the
interface box. Then, press “POWER” again to stow the antenna.
