Winegard SK-1000 Скачать руководство пользователя | Manualshive

Страница: 25 / 27

background image

85

WINEGARD TRAV’LER SK-3003

DIRECTV Triple Wiring Diagram

Notes:

1. A Zinwell WB616 can be substituted for the WB68 to expand the outputs from 8 to 16.
Please refer to the “Zinwell WB616 manual.pdf” or “Zinwell WB68 manual.pdf” file for
maximum cable lengths & all other technical information.

2. B-Band converters must be used on all MPEG4 HD receivers to receive HD
programming.

3. 13V/22KHz port will not be used with the WINEGARD TRAV’LER SK-3003.

«
...
23
24
25
26
27
»

Содержание SK-1000




























Отзывы:

Нет отзывов

Похожие инструкции для SK-1000

Бренд: Maco Antennas Страницы: 7

Бренд: AR Страницы: 24

Бренд: M2 Antenna Systems Страницы: 3

Бренд: Jatontec Страницы: 36

Бренд: Shure Страницы: 4

Бренд: Garmin Страницы: 4

Бренд: TechniSat Страницы: 8

Бренд: Teltonika Страницы: 40

Бренд: H3C Страницы: 6

Бренд: A.H. Systems Страницы: 9

Бренд: KVH Industries Страницы: 49

Бренд: KVH Industries Страницы: 106

Бренд: Kathrein Страницы: 12

Бренд: Kathrein Страницы: 26

BAS-1318 GALAXY Series

Бренд: BAS Страницы: 2

Бренд: 1byone Страницы: 2

Бренд: Dell Страницы: 131

Бренд: Dell Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды