manualshive.com logo in svg

Windsor SC264, Руководство по эксплуатации, Страница: 8 / 33

Поделиться
Скачать
Windsor SC264 Скачать руководство пользователя страница 8

TECHNICAL SPECIFICATIONS 

CUTTER 24V   86039070   04/10/07 

 3-1

 

ITEM DIMENSION/CAPACITY 

Nominal power 

1450 W 

Rated Voltage 

24VDC 

Rated Amperage 

60 Amps  

Batteries 

4 X 6 Volt  250-305-335 AH @  
20 hr rate 

Scrub Brush Motors 

2 X .75 hp (0.56 kW) 

Vacuum Motor 

.75 hp (0.56 Kw) 

Propelling Motor 

.3 hp (0.22 Kw) 

Mass (GVW) 

915 lbs. (415 kg) with 335 AH 

Weight empty without batteries 

346 lbs. (157 kg) 

Solution Control 

Gravity feed, fully variable with 
automatic shut-off in neutral 

Solution tank capacity 

23 gal. (87 l) 

Recovery tank capacity  

25 gal. (95 l) 

Scrub brush diameter for 26 in. (66 cm) scrub head 

13 in (33.0 cm) 

Scrub brush pressure 

Mechanical 80 lbs. (356N) 
Floating 130 lbs. (578N) 
restricted 
 

Scrub brush speed 

200 rpm 

Tires 

2 x 10 in (25.4 cm) non-marking 
foam-filled 

Casters 

2 X 4 in (10.2 cm) polyurethane 
solid non-marking 

Foundation Pressure  

21 lbs./in 

2

 (140 kPa) 

Maximum Speed 

3.2 Miles/hour (5.2 km/hour) 

Coverage with 26 in. (66 cm) scrub head 

31,680 ft

2

/hour at 3.0 mph with  

2 in. overlap* 

Frame Construction 

Steel plate with epoxy 
powdercoat finish. 

Brakes (optional) 

Tire lock parking brake 

Minimum aisle u-turn width with 26 in. (66 cm) scrub head 

69 in. (175 cm) 

Maximum rated climb and descent angle with empty tanks 
and without optional parking brake 

2%  

Maximum rated climb and descent angle with full tanks 
and without optional parking brake 

2%  

 

* Cleaning rate results will vary depending on floor type, building structure, etc.

  

Содержание SC264


































Отзывы:

Нет отзывов