background image

HAZARD INTENSITY LEVEL

M1500  98334  06/29/99

6

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -

WARNING

 and

 CAUTION

 and 

FOR

SAFETY. 

The level of hazard intensity is determined by the following definitions:

WARNING

 - Hazards or unsafe practices which COULD result in severe personal injury or death

.

CAUTION

 - Hazards or unsafe practices which could result in minor personal injury or product or property

damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately.  Do not use the machine if it is not in proper
operating condition.

 

Following is information that signals some potentially dangerous conditions to the

operator or the equipment.  Read this information carefully.  Know when these conditions can exist.  Locate
all safety devices on the machine.  Please take the necessary steps to train the machine operating
personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts.  Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine.

 

Use Windsor approved replacement parts.

!

WARNING

!

CAUTION

Содержание MERIT 1500















Отзывы: