INSPECTION
OPERATION
Please carefully unpack and inspect your machine
for shipping damage. Each unit is operated and thor-
oughly inspected before shipment, and any damage is
the responsibility of the delivering carrier who should
be notified immediately.
ELECTRICAL
This rotary polisher is designed to operate on a standard 15
amp,
115
volt,
60
hz,
AC household
Check that the
voltage shown on the serial number plate is suitable for the
supply available. Voltages below 105 volts or above
125
volts
could cause damage to the motor.
NOTE:
volt
50
models
are available.
,
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This appliance is equipped with a cord hav-
ing an equipment-grounding conductor and grounding
plug. The plug must be inserted into an appropriate out-
let that is properly installed and grounded in accor-
dance with all local codes and ordinances.
WARN NG
Improper connection of the equipment-grounding
conductor can result in
a
risk of electric shock.
Check with a qualified electrician or service person
if
you are in doubt as
to
whether the outlet
is
prop-
erly grounded.
Do
not modify the plug provided
with the appliance
-
if
it will not
the outlet, have
a proper outlet installed by
a
qualified electrician.
This appliance is for use on a nominal 120-volt circuit,
and has a grounded plug that looks like the plug in “Fig.
A
below.
A
temporary adaptor that looks like the adap-
tor in “Fig
.
below
may be used to connect this plug
to
a
2-pole receptacle as shown in “Fig. B below, if a
properly grounded outlet is not available. The tempo-
rary adaptor should be used only until a properly
grounded outlet (Fig. A) can be installed by a qualified
electrician. The green colored rigid ear, lug,
or the like
extending from the adaptor must be connected to a per-
manent ground such as a properly grounded outlet box
cover. Whenever the adaptor
is
used, it must be held
in place by a metal screw.
PROPER GROUNDING
CONNECTION
CONNECTION
USING
AN
ADAPTOR
GROUNDING
Grounding Pin
\ \
I-
Screw
Grounded
Outlet
A
Tab
For Groundina
Screw
Grounded Outlet
Box
ADAPTOR
flg.
B
NOTE: Adaptors
are
not allowed In Canada.
Fig.
C
CAUTION: For indoor
U s e
Only.
To prevent
damage to the floor
when using the Brush optlon, use water or other
approved
solution
operating.
When using the pad optloln, always keep
the machine moving when In contact with the
WARNING:
HIGH
TORQUE.
HOLD MACHINE FIRMLY
BOTH
HANDS.
1
.)
Ensure that the pad driver
or
brush is installed correct-
ly and in good shape. Install or change pad if necessary
(See Page 3
for
of
Installation).
2.)
Plug the machine into a wall outlet
as
described in the
grounding instructions.
3.)
Lower the handle
by unlocking the adjustment handle
and moving the handle into position.
the handle
when it is in a comfortable position.
4.)
Check to be sure the pad driver or brush is installed
before starting.
5.)
With the switch
rotated forward, squeeze one
of the switch levers, turning the machine on. (These levers
can be operated independently
of each other)
6.)
To
stop the machine, release the switch lever
and
switch lock.
NOTE
The machine is equipped with a circuit breaker
to
protect the motor in the event
an
overload condition
occurs. The circuit breaker is located
at
the bottom of the
switch housing. Push the reset button to restart the ma-
chine. If the breaker trips again, correct the cause of over-
loading before proceeding.
7.)
Do not let machine rest on pad. When finished with the
machine for the day return handle to the storage position.
Be sure to leave machine in a
safe
place where there is no
risk of being tipped over.
CONTROLS
Page
2
