Windpilot PACIFIC PLUS Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 26

Windpilot PACIFIC PLUS Скачать руководство пользователя страница 1

PACIFIC PLUS

WELCOME

1.0 INSTALLATION

1.1 Tools
1.2 Installation Options
1.3 Points to Consider before Installation

1.3.1 Assembling the System after Delivery
1.3.2 Positioning the System
1.3.3 Bad Air and the Windvane
1.3.4 Auxiliary Rudder and Main Rudder
1.3.5 On Land or in the Water?

1.4 Installation: Quick Guide

1.4.1 The Five Criteria

1.5 Installation: Comprehensive Guide

1.5.1 Height above the Waterline
1.5.2 Vertical, Canoe and Traditional Overhanging Sterns

1.5.2.1 Making the First Connection
1.5.2.2 The Mounting Block
1.5.2.3 Mounting the Pendulum Rudder Module
1.5.2.4 Alignment
1.5.2.5 Fitting the Cross Brace
1.5.2.6 Making the Second Connection
1.5.2.7 Fore and Aft Correction
1.5.2.8 Lateral Correction

1.5.3 Forward-raked Sterns and Bathing Platforms

1.5.3.1 Fore and Aft Correction
1.5.3.2 Lateral Correction

1.5.4 Be Aware
1.5.5 Do I Need to Reinforce the Transom?
1.5.6 What if the System is Aligned Incorrectly?
1.5.7 Remote Control
1.5.8 The Pendulum Rudder

1.5.8.1 Mounting the Rudder Blade
1.5.8.2 Positioning the Rudder Blade
1.5.8.3 Overload Protection
1.5.8.4 Pendulum Rudder Lift-up

1.5.9 Setting the Main Rudder

1.5.9.1 Mechanical Wheel Steering
1.5.9.2 Hydraulic Wheel Steering

1.5.10 WINDPILOT and Autopilot

1.5.10.1 Configuration

2.0 SAILING WITH YOUR WINDPILOT

2.1 WINDPILOT System Requirements
2.2 Sailing with Your Windpilot: Quick Guide
2.3 Sailing with Your Windpilot: Comprehensive Guide

2.3.1 System Not in Use
2.3.2 Preparing for Use

1
2
3
...
»

Содержание PACIFIC PLUS



























Отзывы:

Нет отзывов