background image

Page 2 of 6                                                                                                                                                       Instal Instr Electric Cooktop CTE P Rev B.doc 

SOLID SURFACE COUNTERTOPS

 

 Consult counter manufacturer for requirements. 

 

Countertops made from natural (i.e. granite) or Solid Surface Materials (i.e. Surell™) require special cutout 

preparation and installation procedures. Follow all guidelines in preparing the cutout. 
 

 

Round the cutout corners according to instructions from the countertop manufacturer. 

 

 

Apply heat reflective tape (i.e. Scotch Aluminum Foil Tape #425 or #427) around the cutout so that it folds 
over the top and inside surfaces of cutout. Be sure tape extends to the outermost edge of the cooktop. Cover all 
corners with tape. See FIG 

 2. 

 

 

Install the cooktop and secure to countertop as instructed in next section. 

 

 

Trim the excess, aluminum tape along the frame edges. Use care in trimming tape to avoid scratching 
countertop or stainless steel frame. 

 

COOKTOP INSTALLATION 

 

WARNING 

 DISCONNECT POWER BEFORE INSTALLING COOKTOP. BEFORE 

TURNING POWER “ON” BE

 SURE THAT ALL CONTROLS ARE IN THE 

“OFF” POSITION.

 

 
FOAM TAPE 

 A foam tape is provided to seal the cooktop edges to the countertop. Turn the cooktop upside 

down and apply the tape to bottom side and back edges of stainless steel frame. The tape should be 
approximately 1/16 inch from the edge of the stainless steel frame. See FIG 

 3. 

 
Fastening Cooktop 

 After centering the cooktop in the countertop opening, install the 2 screws provided in the 

side brackets of the countertop. Position a wood block between the end of the screw and the 
countertop, and tighten the screw. 

Do not tighten the screw directly against the 

countertop. See FIG 

 4. 

 

ELECTRICAL CONNECTION 

 

Attach flexible conduit, three (3) foot cable, located at right rear corner of cooktop bottom, to junction box. 

 

 

Connect cooktop lead wires to junction box supply wires, in proper phase: black to black (L1), white to white 
(neutral), red to red (L2), 

and bare wire to ground

. This will result in compliance with the National Electrical 

Code. 

 

 

Location of Data Plate bottom of cooktop. See FIG 

 3. 

 

START UP TEST 

 

 

Remove all items from cooktop 

 

Clean cooktop with cooktop cleaning crème or clean damp cloth.

 

 

Check to see that all controls are in the off position. 

 

Turn power on at service panel. 

 

Turn controls on to check unit operation. Check Power On and Surface Hot signal light operation. 

 

Turn controls off after checking operation. 

 
 

 

 
 

Содержание CTE36P







Отзывы: