WilTec 61958 Скачать руководство пользователя страница 7

Technical data

Intake voltage

 (V)

230

Frequency

 (Hz)

50

Compressor power

 (W)

1100 (1.5 hp)

Max. rotation speed 

(rpm)

2850

Suction capacity

 (ℓ/min)

206

Tank capacity 

(ℓ)

50

Noise level

 (dB (A))

83

Max. operating pressure 

(bar)

8

Test pressure 

(bar)

12.6

Temperature range

 (

)

5–150

Weight

 (kg)

30

Connections

NW7.2

Equipement

Thermal motor protection

2 compressed air connections

2 pressure gauges

1 pressure reducer

Oil lubricated

Pressure relief valve

Before commissioning

Place the compressor in a clean, dry and well-ventilated place.

Use only 230 V operating voltage with a maximum fluctuation of 5 %.

At the oil level, check whether it is within the red display circuit.

Use SAE30 gear oil when the ambient temperature is above 10 

. If the ambient temperature

is below 10 

, use SAE10 gear oil.

Open the drain valve, adjust the pressure and let the compressor run for 10 min without any
equipment connected so that all moving parts lubricate themselves.

Settings

The compressor is secured by a pressure switch. As soon as the max. boiler pressure is
reached, it switches off automatically. As soon as the pressure has fallen below the minimum
rate,   it   switches   on   again.   This   pressure   setting   was   made   ex   factory   and   must   not   be
changed. As soon as the engine switches off, the compressed air in the discharge pipe should
be released by the release valve under the switch. This works automatically and is necessary
to avoid damaging the engine. The pressure can be varied by turning the screw bolt.

The discharge pressure can be adjusted by the pressure regulator.

When you turn off the compressor, turn it off with the on/off switch.

Specific safety instructions

First remove the gear oil cover and insert the red plug.

Never unscrew a connection when the tank is under pressure.

Never disconnect an electrical connection when voltage is applied to the mains plug.

Never change the settings of the safety relief valve.

Make sure that the mains voltage does not deviate from 230 V by more than 5 %.

© by WilTec Wildanger Technik GmbH 

Item 61958

Page 7

http://www.WilTec.de
http://www.aoyue.eu  

  

02 2021

-1

http://www.teichtip.de

Содержание 61958













Отзывы: