Wilson Electronics Tri-Band 4G-C Скачать руководство пользователя

Страница: 5 / 16

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Signal

Booster

Lightning

Surge Protector

(recommended)

Splitter

(if using multiple

Inside Antennas)

(Optional

third antenna

for additional

coverage) .

Inside Antenna

Surge Protector

Powerstrip

Before Getting Started

This guide will help you properly install your Wilson Electronics Signal

Booster .

It is important to read through all of the installation steps

for your particular application prior to installing any equipment.

Read through the instructions, visualize where all the equipment will

need to be installed and do a soft installation before mounting any

equipment . Contact Wilson Electronics Technical Support with any questions

at: 866-294-1660 .

Содержание Tri-Band 4G-C

















Результаты поиска

Содержание Tri-Band 4G-C

Отзывы:

Похожие инструкции для Tri-Band 4G-C

Бренды по названию

Популярные бренды

Wilson Electronics Tri-Band 4G-C, Руководство по установке

Результаты поиска

Содержание Tri-Band 4G-C

Отзывы:

Похожие инструкции для Tri-Band 4G-C

Бренды по названию

Популярные бренды