1
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
Installation Instructions for the Following
Wilson Electronics Signal Booster:
iDEN 800 MHz Adjustable Gain In-Building Wireless
Smart Technology ™ Signal Booster
How it Works
Wilson Electronics Signal Boosters are bi-directional devices that deliver
service levels consistent with what would be expected in areas of high
cell network coverage. They amplify a weak or shadowed signal in
mobile, M2M, marine and in-building applications. When using a Wilson
Electronics Signal Booster in conjunction with Wilson Electronics
antennas, the Outside Antenna will collect the cell tower signal and send
it through the cable to the Signal Booster. The signal is then amplified
and re-transmitted through the Inside Antenna into the room. Cell
phones and cellular data cards in that area then communicate with the
improved signal. When a cell phone or cellular device transmits, the
signal is received by the Inside Antenna, amplified by the Signal Booster
and transmitted back to the cell tower through the Outside Antenna.
Inside this Package
Signal
Booster
7V AC/DC
Power Supply
(included in some kits)
To purchase, call Wilson Electronics Sales Department at: 800-204-4104
Outdoor Antenna Options
Indoor Antenna Options & Accessories
1. 800 MHz Yagi Antenna (301111)
2. 800 MHz Yagi Cellular Antenna (301129)
3. Wide Band Directional Antenna
700 - 2700 MHz (304411)
4. Outdoor Panel Antenna
700-2700 MHz (301157)
A. Wide-Band Panel Antenna 700-2700MHz (301134 & 301135)
B. 50 Ohm Lightning Surge Protector with N-Connectors
(859902)
Splitter options on page 8
3
1
2
B
A
4
Note: Kits may contain different accessories
Select a location to install the Signal Booster that is away from
1.
excessive heat, direct sunlight, moisture and has proper ventilation.
Do not place the Signal Booster in an air-tight enclosure.
Select a location on the roof of the building to install the Outside
2.
Antenna (see page 5). Use a cell phone in test mode to find the
strongest signal from the cell tower. (see page 6). Visit
www.WilsonElectronics.com
to find the test mode function for your
particular cell phone.
Run the Outside Antenna cable to the Signal Booster and attach it to
3.
the connector labeled “Outside Antenna” on the Signal Booster. Run
the Inside Antenna cable to the Signal Booster and attach it to the
connector labeled “Inside Antenna” on the Signal Booster. See page
7 for more information on running cable. Lightning Surge Protection
is recommended for all in-building installations (see page 6).
Select a location for the Inside Antenna, preferably in the center of
4.
where the signal needs to be amplified (see page 8). A minimum
separation distance of 20
vertical
feet is necessary for operation. If
the inside coverage is not sufficient you may need as much as 75 feet
of
horizontal
separation. See installation diagram on pages 3 & 4.
Before powering up the Signal Booster, verify that both the Outside
5.
Antenna and the Inside Antenna are connected and check that
all connections are tight (see page 9).
Note: Be careful when
plugging the connectors in so as not to bend the center pins on the
connectors.
The Signal Booster has been packaged with the gain control knobs
6.
adjusted to the highest gain position. If the light is not green, please
refer to pages 10-11.
Quick Install Overview
See Installation Diagram on page 3. Contact Wilson Electronics Technical
Support Team with any questions at 866-294-1660.
Appearance of device and accessories may vary.
Model #274080
Warning:
Connecting the Signal Booster directly to a cell phone with
use of an adapter will damage the cell phone and/or the
Signal Booster.
Wilson
®
Electronics recommends that all AC power
supplies for home electronics be plugged into a
Surge Protector Power Strip.
