5
Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6 pm mountain standard time.
5
6
Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660
Or email: [email protected] Hours: 7am to 6 pm mountain standard time.
Powering up a Wilson Electronics Signal Booster
(In-Building & In-Vehicle)
For
in-vehicle
, first connect the power cable
to the Signal Booster input marked “12V DC”
and then insert the large end into a power
socket or vehicle power adapter .
The Signal Booster may remain on all the
time; however, leaving the Signal Booster
on in a vehicle when it is not running can
discharge the battery in a day or two .
Carefully insert the
power cable .
Warning:
Use only a Wilson
Electronics power supply . Use of a
non-Wilson Electronics product could
damage your equipment .
!
Testing a Wilson Signal Booster
To test your Signal Booster, go to a weak signal area where your cell phone registers only
1-2 bars without the Signal Booster turned on . Then, connect the Signal Booster to the
phone and you should see a signal improvement of 2 or more bars .
Note: Many phones
take up to 20 seconds to reset the bar indicator.
Extension Cables
Available for purchase at
www.WilsonElectronics.com
or by calling 800-204-4104, to help
you customize your installation for peak performance .
Warning:
Verify that both the Outside
Antenna and the adapter extension cable
are connected to the Signal Booster before
powering up the Signal Booster .
!
Warnings and Recommendations
Warning:
Verify that both the Outside Antenna and the adapter extension cable are
connected to the Signal Booster before powering up the Signal Booster .
Warning:
RF Safety
: In-vehicle - The Outside Antenna must be installed with a
separation of at least 20 inches from any of the vehicle’s occupants or
nearby persons and must not be located or operating in conjunction
with any other antenna or Signal Booster . Use of a Cellular Signal
Booster with an antenna gain higher than 6 .12 dBi is in violation of FCC
regulations, for which the offender is fully liable . All Wilson Electronics
mobile antennas are 6 .12 dBi or less .
Warning:
RF Safety
: In-vehicle - All roof mount antennas should be centrally located
on the roof of the vehicle . Glass Mount Antennas should be located in
the middle of either the front or back windshield . Mirror Mount Antennas
should be at least 20 inches from any persons in or around the vehicle .
A good option is to power the Signal Booster through the ignition switch so that the Signal
Booster turns off and on with the vehicle . (
Part# 859905
12V DC Hardwire Kit available
from
www.WilsonElectronics.com
) .
For
in-building
, first connect the AC/DC power supply to the Signal Booster input labeled
“12V DC” and then into a wall outlet . (included in 811200)
Warning:
RF Safety
: In-Building - The Outside Antenna must be installed on an
outdoor structure with a separation of at least 26 inches from all persons
during normal operation . The outside building antenna must not have a
gain that exceeds 15 dBi . All Wilson Electronics outside building antennas
have gains of 15 dBi or less .
Lightning protection is recommended for all in-building installations . (sold separately)
NOTE:
The aluminum casing of a Wilson Electronics Signal Booster will adjust very quickly
to the ambient temperature of its environment. For example, in the summer, when the
inside of a car can reach 140 degrees Fahrenheit, the Signal Booster temperature may be
150 degrees or higher. The casing will be hot to the touch, similar to a metal door handle
or a steering wheel. Such high temperatures will not damage the Signal Booster, nor do
they pose a fire risk to the vehicle. As recommended in these instructions, install the Signal
Booster in a location with adequate ventilation, such as under the seat, in the trunk or under
the dashboard. Keep the area free of items that could block air flow to the Signal Booster.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back
guarantee . If for any reason the performance of any product is not acceptable, simply return the
product directly to the reseller with a dated proof of purchase .
1-Year Warranty
Wilson Electronics Signal Boosters are warranted for one (1) year against defects in workmanship
and/or materials . Warranty cases may be resolved by returning the product directly to the reseller
with a dated proof of purchase .
Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense,
with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied
by Wilson Electronics . Wilson Electronics shall, at its option, either repair or replace the product .
Wilson Electronics will pay for delivery of the repaired or replaced product back to the original
consumer, if located within the continental U .S .
This warranty does not apply to any Signal Boosters determined by Wilson Electronics to have
been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or
electronic properties .
RMA numbers may be obtained by phoning our free U .S . based Technical Support at 866-294-1660 .
The Manufacturer’s rated output power of this equipment is for single carrier operation .
This device complies with part 15 of the FCC Rules . Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation . Changes or modifications made that
are not expressly approved by Wilson Electronics could void authority to operate this equipment .
One or more of the following U .S . Patent numbers may apply to the Signal Booster in this product –
D596,614; D596,615; D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186; 7,783,318; 7,684,838;
12,714,994 .
Disclaimer: The information provided by Wilson Electronics, Inc . is believed to be complete and
accurate . However, no responsibility is assumed by Wilson Electronics, Inc . for any business or
personal losses arising from its use, or for any infringements of patents or other rights of third
parties that may result from its use .
Copyright © 2011 Wilson Electronics, Inc . All rights reserved .
In-Building / In-Vehicle