Williams Sound R801 Скачать руководство пользователя страница 10

  Williams Sound 

® 

Helping People Hear

10

PERSONAL PA

®

FM M

ONITOR

R

ECEIVER

S

PECIFICATIONS

M

ODEL

R801

Dimensions, Weight:

1.75" H x 8.45" W x 8.25" D, 3lbs.

Color:

Black epoxy paint with white legends

Rack Mount:

One EIA rack space high, 1/2 space wide, 1-2 units can be mounted in a single rack space
with optional RPK 005 (single) or RPK 006 (double) Rack Mount kits.

Power:

24VAC, 50/60Hz, TFP 016 supplied, Molex connector

Power Indicator:

Green LED, Front panel

Operating Freq.:

10 Channel Selectable (72.1, 72.3, 72.5, 72.7, 72.9, 74.7, 75.3, 75.5, 75.7, 75.9 MHz*)

Freq. Accuracy:

0.01%, Frequency Synthesized, Crystal Reference

FM Deviation:

+/- 75kHz, 75µS de-emphasis

Sensitivity:

0.8µV at 12 dB Sinad with squelch at minimum

Carrier Indicator:

Green LED, Front panel

Freq. Response:

50 to 18kHz, +1, -4 dB

Signal/Noise Ratio:

60 dB at 100µV.

Receiver Antenna:

Flexible “rubber duckie” type or optional 75 Ohm remote antenna

Controls:

Power On/Off, FM Channel, Squelch.

Distortion:

less than 1.0% at rated power

Phones Output:

1/4” TRS, 10mVrms @ 50 Ohms impedance.

Line Output:

1/4” TRS, Balanced (Tip is positive, Ring is negative, Sleeve is common) or Unbalanced (Tip or
Ring can be connected to the Sleeve), nominal output: +4dBm @ 600 Ohms, 1.2Vrms

Additional Notice:

This device complies with the requirements of Industry Canada (IC), as specified in document RSS-210. The device is
permitted only on a no-interference no-protection basis, that is, it must cease operation when it is determined (such as
by turning the device on and off) that it causes harmful interference to services authorized by IC. Authorized services are
listed in the Canadian Table of Frequency Allocations or as determined by IC from time to time. Also, the operator must
accept any radio interference received, including interference that may cause undesired operation of the device.

Williams Sound Corp.

10399 West 70th St., Eden Prairie, MN 55344-3459

U.S.A.  800-328-6190 / 952-943-2252 / FAX: 952-943-2174

www.williamssound.com

© 2000, Williams Sound Corp.            MAN 098 B

Содержание R801











Отзывы: