Wilcoxon Research PA8HF Скачать руководство пользователя страница 3

 

 

 

 

 

         Page 3 of 12 

WARNING: OPERATION OF THIS AMPLIFIER IS SAFE WHEN THE INSTRUCTIONS IN THIS 
MANUAL ARE READ THOROUGHLY BEFORE THIS SYSTEM IS CONNECTED TO 
ELECTRICAL POWER.  PARTICULAR ATTENTION MUST BE PAID TO THE SAFETY 
SECTION OF THIS MANUAL.  IT IS THE ULTIMATE RESPONSIBILITY OF THE USER TO 
SAFELY SET UP, OPERATE AND MAINTAIN THE SYSTEM.  REPLACE FUSES ONLY WITH 
THE SAME TYPE AND RATING AS INDICATEDIN THIS OPERATING GUIDE. 
 
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT 
TO RAIN OR MOISTURE. 
 
WARNING:  LETHAL VOLTAGES ARE PRESENT IN THE AMPLIFIER AND MATCHING 
NETWORKS. THE AMPLIFIER CONTAINS ENERGY STORING DEVICES. THEY MUST BE 
ALLOWED TO DISSIPATE ENERGY BEFORE OPENING THE AMPLIFIER ENCLOSURE. 

 
 

Safety section 

 
The power amplifier can be safely operated when the instructions in this manual are carefully 
followed. 
 
This section summarizes the safety considerations.  Reminders, in the form described below, will 
appear in the detailed instructions to assure operator awareness of these safety considerations. 
Qualified personnel should operate and maintain this power amplifier only after becoming 
thoroughly familiar with this manual. 
 
 

WARNING:  This symbol is used in the instruction manual where operator safety 
must be considered.  The instruction manual should be consulted and read carefully. 

   
 
 

CAUTION: This symbol is used when caution is needed to prevent damage to 
equipment.  It is used where careful attention to certain procedures described in the 
instruction manual is needed.  This symbol is also used to emphasize procedures 
other than normal operating procedures. 

Содержание PA8HF













Отзывы: