wiking 0774 10, Руководство по эксплуатации, Страница: 15 / 38

16
Turn on the remote control module by pres-
sing the logo . The logo illuminates red.
The remote control module is ready for ope-
ration.
Important information:
The model must always be switched on first,
followed by the remote control module.
Now the connection between the model and
the remote control module is established.
This process can take up to five (5) seconds.
The connection between the remote control
and the model has been established when the
level A button (vehicles) and the headlights
and rear lights shine constantly. The model
is saved in the remote control module and is
ready to run. The model can be operated only
with this remote control module during this
driving sequence. Driving can begin.
5.2 Multiple operators/users – multiple
models
Before beginning a driving sequence with
several drivers and models, the systems of
the individual drivers must be started. To
ensure that the remote control modules find
only the models of the respective individual
driver, each individual driver has to start up
his system separately, one after another. The
procedure for the start is the same as descri-
bed in section 5.1.
Example:
4 people want to drive 4 WIKING
CONTROL 87
models in a room together.
To ensure that everything runs smoothly, the
systems have to be started one after another.
To begin with, all remote control modules
and models have to be switched off. Driver
1 now switches on his model and then his
remote control module. If driver 1’s level A
LED is shining, then his system is operatio-
nal. Only then can driver 2 follow the proce-
dure. Once his level A LED is shining, then
it is the turn of driver 3, followed by driver 4.
Important information:
Error-free driving will be possible only if
this rule is strictly observed.
5.3 Addition of further models
Using the WIKING
CONTROL 87
radio
system, you can control an almost limitless
number of different models. If you have
started your system with a single model, and
after a time you want to add an additional
model, then your remote control module has
to find and save this model.
Leave the remote control, and the model
which you are already driving, switched on.
If you now switch the battery‘s operating
switch from OFF to ON for the model which
you want to add, then the model’s lighting
will begin to flash quickly. This is a signal
that the model is ready to connect itself with
the remote control module. To connect this
model with the remote control module, press
the SCAN button. After the connection has
been successfully established, this model is
allocated to the corresponding LEVEL, and
is available immediately. During the SCAN
process, the corresponding level button
goes out and comes back on again, once the
connection has been established. The model
stored on this level up to now is not lost, but
is kept in the background. By pressing the
corresponding level button you can switch
between both the models of a level. Repeat
this procedure for further models.
The model that was last added is always the
operational one. If you now want to switch
between levels, press the level button once
(or more than once depending on the number
of models stored). Every time this button is
pushed, the next model that is saved is trig-
gered. A change in the level can take 3 to 10
seconds.
5.4 Deleting the model from the memory
Turning off the remote control module dele-
tes the models stored in the internal memory
of the module. If there are several vehicles,
and a vehicle is switched off, it is deleted
from the internal memory.
6. Maintenance and cleaning
Use only dry and dust-free cloths to clean
and care for the WIKING products. In order
to guarantee the design-related safety level
of this model in the long term, the model
must be checked regularly for any visible
damage.
7. Disposal of disused electrical equipment
At the end of their useful life, these products
must not be disposed of as normal household
waste; instead they must be handed in to a
collection point for the recycling of electrical
and electronic devices. This is indicated by
the symbol on the product, in the instructions
for use, or on the packaging. The materials
are recyclable as specified by their labelling.
You make a major contribution to the pro-
tection of the environment by recycling, sal-
vaging materials, or re-using spent goods in
other ways. Please consult your local autho-
rity about the waste collection point in your
area.
GB
3521_Bedienungsanleitung_ALLE_WIKING_RC_print.indd 16 13.06.14 12:30