![background image](http://html.mh-extra.com/html/whyte/e-150/e-150_operating-instructions-and-owners-manual_978502021.webp)
Page 20
2019
Assemble the Shield Washer components (Items 19 in figure 5 or items 2 or 3 in fig-
ures 6 & 7). If you have applied enough grease, it should spread from under the
Shield Washer or Spacer components as they are positioned. Wipe this excess grease
away from around the Shield Washer or Spacer components.
6.2.4: Application of
“
SKF LGAF 3E
”
or
“
Castrol Optimol T
”
Anti
-
Fret Pastes
Once the H Link & Swinging Arm components have been assembled correctly, either
SKF LGAF 3E or Castrol Optimol T paste
must
be applied to all outside faces of the
Shield Washer components (Items 2 & 3 in Figures 6 & 7) that contact the Main
Frame and Swinging Arm. It is additionally recommended to apply anti
-
fret paste to
the mating contact surfaces on the Main
Frame and Swinging Arm.
6.3: RE
-
ASSEMBLING THE REAR SUSPEN-
SION.
6.3.1: Re
-
assemble the Rear Suspension
Tools Required:
2x 5mm Hex Key
2x 6mm Hex Key
2x T
-
25 Torx® Key
Torque
Wrench
(Ranging from
5Nm
to
25Nm)
Reference figures 3,4,5,6 & 10. The re
-
assembly of the Rear Suspension is essen-
tially the reverse of the dis
-
assembly procedures 6.1.1, 6.1.2 & 6.1.3.
6.3.2 To re
-
assemble the Chain
-
stays (14) and Bearings (20) into the Main
Frame (15)
-
First Stage.
Before inserting the Bearings, make sure all the components are clean from dirt and
have been thoroughly de
-
greased. Apply a small amount of Loctite 638 to the out-
side diameter of the Bearing and to the inside mating bore of the Main Frame (15).
Using the press tools shown in Figure 8 & 9, insert the BOLU
-
WB0025 Bearings (20)
into both sides of the Main Frame (15). Ensure the spacer (21) is located between
the Bearings (20).
Referencing figure 5, apply either SKF LGAF 3E or Castrol Optimol T paste to all
faces of the Shield Washers (19), Pivot Pin (12) and Screw (10). Place the Shield
Washers (19) alongside the Bearings (20). Insert & align the Chain
-
Stays (14) be-
tween the Washers (19). Insert the Pivot Pin (12) from the left side of the Chain
-
Stays (14). Screw the Pivot Pin (12) io the thread in the right side of the Chain
-
Stays (14). Insert the Tapered Sleeve (11) and screw in the M6 x 20mm long Cap-
screw (10).
WHYTE Service Manual
Figure 10: Correct
Orientation
Содержание E-150
