Whittier Wood Furniture Ellison 2138ASTa Скачать руководство пользователя

Страница: 7 / 8

2138ASTa Ellison 70"W Low Dresser

Assembly Instructions

2138ASTa — Page 7 — 05/20

Furniture Tipping Restraint Instructions

Safety First! Anchor It!

Before you begin this assembly, identify each part and make sure the quantities received match what is on this

list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following

list for its name and letter code.

Part

Description

Quantity

Cam Buckle and Short Strap (installed)

Plastic Bracket (installed)

1" x 1000mm Long Strap (installed)

#8 x 3" Pan Head Screw

#10 x 1" Oval Head Screw (inserted)

Washer

If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard

and floor see the instruction included inside the tipping restraint kit for an alternate

installation.

7. Decide where you want to place the piece of furniture in your room. Mark the baseboard with a

pencil mark directly behind the location where the tipping restraint is attached to your item.

Move the item away from the wall far enough to allow you to access the spot where the

baseboard meets the floor. Position the straps and Plastic Bracket (B) as shown in Figures 7

and 7a with the angled corners of the Plastic Bracket (B) firmly placed against the seam of the

baseboard and floor. Attach by driving #8 x 3" Pan Head Screws (D) through the holes in the

Plastic Bracket (B) into the seam below the baseboard where it meets the floor. See Figures 7

and 7a.

Fig. 7

x 2

Fig. 7a

Wall

Floor

Baseboard

Содержание Ellison 2138ASTa









Результаты поиска

Содержание Ellison 2138ASTa

Отзывы:

Похожие инструкции для Ellison 2138ASTa

Бренды по названию

Популярные бренды

Whittier Wood Furniture Ellison 2138ASTa, Руководство по сборке

Результаты поиска

Содержание Ellison 2138ASTa

Отзывы:

Похожие инструкции для Ellison 2138ASTa

Бренды по названию

Популярные бренды