background image

7

Ch4 BeachHunter 300 Controls

Ground

The Ground control adjusts the level of rejection 

against ground mineralization. When set properly 

the detector will ignore most common ground in-

cluding salt. Fine tuning the GROUND control for 

the area will improve performance particularly  

when the All Metal mode is used.

To fine tune the GROUND control first go to the 

area you wish to search.

Place the loop on the ground (search height).

Turn the THRESHOLD control clockwise until a 

slight hum (threshold of sound) can be heard.

Place the TOGGLE in the All Metal position.

Pump (lift and lower) the loop from the ground rais-

ing about four inches and lowering to search height 

while listen to the threshold.  The threshold will 

either stay the same (desired), increase in volume, 

or decrease in volume.

Pay attention to the change in sound 

only

 as the 

loop approaches the ground.  

If the threshold sound decreases as the loop ap-

proaches the ground, start turning the GROUND 

control “clockwise” or “up” slowly while continu-

ing to pump the loop over the ground. 

If the threshold hum increases in volume as the 

loop approaches the ground, start slowly turning the 

GROUND control “counterclockwise” or “down” 

while continuing to pump the loop over the ground.

Once completed, switch the toggle switch to the 

DISC setting if trash rejection is desired 

TOGGLE IN
ALL METAL
POSITION

Think of the GROUND control as a volume 

level for the ground. With the loop approach-

ing the ground, if the “hum” gets louder, turn 

the control down. If it gets softer, turn the 

control up. The goal is to find the ground set-

ting that allows little or no change in threshold 

“hum” as the loop is lowered and lifted from 

search level. If a steady “hum” is difficult to 

accomplish, slightly reduce the SENSITIV-

ITY control (turn counterclockwise) and try 

again.

Tips on Ground “Balancing”

Содержание BeachHunter 300

















Отзывы: