background image

WHITEHALL MANUFACTURING

 • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.

Phone 800-782-7706 • 626-968-6681 • Fax 626-855-4862 • Web: www.whitehallmfg.com

Operating & Maintenance Manual for Whitehall Electric Bottle Warmers

5

SETTING UP

1. Your new Bottle Warmer includes the following:

 

Additionally each model contains the following:

Wall mounting hardware plackage 

 

• 

(See instructions below)
Warranty registration card

• 

(This) Operating & Maintenance Manual

• 
If you are missing anything, please call the phone number 

listed below.

2. Unpacking your Bottle Warmer

Remove  all  shipping  material.  Remove  the  dispensing 

bottles. Clean the unit and dispensing bottles thoroughly 

before using.

3. Device Placement

Place the Bottle Warmer at a convenient level, such as on 

a table or a scratch-resistant counter-top. Before moving 

the Bottle Warmer, unplug and cool the unit. The unit may 

also be wall mounted using the instructions below. 

Model EBW-1

(1) One-bottle 

 

      warmer unit

(1) 8-ounce (237 ml) 

 

      plastic dispenser 

 

      bottle

 

Model EBW-2

(1) Two-bottle 

 

      warmer unit

(2) 8-ounce (237 ml) 

 

      plastic dispenser 

 

      bottles

 

Model EBW-4

(1) Four-bottle 

 

      warmer unit

(4) 8-ounce (237 ml) 

 

      plastic dispenser 

 

      bottles

 

The anchors and screws 

support the Bottle Warmer 

and full bottles only. Putting 

additional weight on the unit 

may cause failure. This can 

damage the Bottle Warmer 

and may result in injury.

Step 1 -   Collect the the tools you will need: hammer, Phillips screwdriver, tape, ruler, level
Step 2 –  Using the hammer, pound the anchors straight into the wall, using the guide above.

 

Make sure the anchors match these center to center dimensions:

 

 

For Model EBW-1 

 

For Model EBW-2 

 

For Model EBW-3

 

 

3” Vertical 

 

 

4-7/8” Horizontal  

 

11-7/8” Horizontal

Step 3 –  Using the Phillips screwdriver, turn the #8 screw clockwise into the anchor until it stops. 

 

Turn the screw one full turn counter-clockwise.

Step 4 –  Align the slotted holes in the back of the Bottle Warmer with the screws in the wall. 

 

Slide the Bottle Warmer down onto the screw until it stops. See the "ON INITIAL USE" Instructions on page 6.

WALL 

MOUNTING 

SIDE VIEW

!

CAUTION

Drywall

Anchor

#8 Screw

Bottle Warmer

Содержание EBW-1













Отзывы: