manualshive.com logo in svg

White Outdoor Series 900, Руководство оператора, Страница: 14 / 17

Поделиться
Скачать
White Outdoor Series 900 Скачать руководство пользователя страница 14

14

6

WARNING

Always stop engine, 
disconnect spark 
plug, and ground 
against engine before 
cleaning, lubricating 
or doing any kind of 
maintenance on your 
machine.

Cutting grass in 
sandy soil condition 
causes abrasive wear 
to the blade.

If unit is tipped for 
easier access to 
blade or belt, tip 
mower as specified 
in separate engine 
manual. If it does not 
specify turn mower 
on its side making 
sure that the air filter 
and the carburetor 
are up.

Maintenance

10. Using a pair of pliers, pull back and rotate belt keeper 

bracket from the slot on idler pulley.

11.  Slide the belt out from between the belt keeper 

bracket and the idler pulley. See Figure 16. 

12. Squeeze the belt together and push belt forward. 

Press the control arm inward towards the deck and 
remove the six speed cable from the slot. See Figure 
17.

13. Pivot the control arm down away from the pulley and 

belt.

14. Lift off the lower pulley assembly and remove the old 

belt from around the crankshaft.

15. Place the new belt over the transmission pulley. Start 

the belt in pulley groove and rotate pulley until belt is 
seated in transmission pulley.

16. Place belt between idler pulley and the belt keeper 

bracket.

17. Using pliers, rotate the belt keeper bracket so that it 

snaps into slot on the idler bracket.

18. Tighten the idler pulley bolt and locknut ½ turn using 

two 7/16” wrenches.

19. Place belt between the two pulley halves on the 

crankshaft. Make sure to route the belt inside the belt 
guard pin. See Figure 18.

20. Pinch belt together so that it is not in the pulley 

groove, and the lower pulley can be pushed towards 
the engine. See Figure 19.

21. Pivot the control arm back to its original position and 

reinstall the six-speed cable into the slot.

22. Check and make sure the belt is routed inside the 

pulley halves and the belt guard pin.

23. Reinstall the bolt securing transmission to rear mower 

housing.

"ELT'UARD

0IN

Figure 16

3IXSPEED

CABLESLOT

Figure 17

Figure 18

Figure 19

Содержание Series 900


















Отзывы:

Нет отзывов