White Outdoor LT 542H Скачать руководство пользователя | Manualshive

Страница: 34 / 48

background image

Page 6

Four-Cycle Engine • Vertical Crankshaft • Air-Cooled

181-887-14

V. Starting Your Engine

An adult should start the engine.
Only allow children to start engine if

an adult has determined they are experienced and capable
of such operation.

If you are unable to start this engine
after following instructions in this

manual, contact your Authorized Tecumseh Servicing
Dealer. To avoid serious burn injuries or damage to your
engine, DO NOT attempt to start or troubleshoot this engine
in any other way. For example:

• DO NOT use starting fluid.

• DO NOT spray flammable vapors into carburetor or

onto air cleaner.

• DO NOT put flammable liquids into carburetor or

onto air cleaner.

• DO NOT operate engine or pull on starter rope with

spark plug removed. Fuel can spray from spark plug
hole and ignite.

This section contains starting instructions for electric and
manual start engines. In order to locate the instructions that
apply to your engine, first determine what type of starter
you have. If you have an electric starter see “A. Engines
with Electric Starters” instructions. If you have a manual
recoil starter see "B. Engines with Recoil Starters"
instructions on page 8.

A. Engines with Electric Starters

Only one of the following two sections will apply to your
engine. See Table 3.

I. Combined Speed and Choke Control

1. To avoid carbon monoxide poisoning, be sure engine is

outdoors in a well-ventilated area.

2. Move combine control to “CHOKE” or “START” position

(see equipment manufacturer’s instructions). See Fig-
ures 8 and 9.

NOTE

If restarting a warm engine after a short shutdown, move
combined control to “FAST” instead of “CHOKE” or “START”
position. See Figures 8 and 9.

3. Push starter button or turn ignition switch key (see

equipment manufacturer’s instructions) to start engine.

NOTES

If engine fails to start after 3 attempts repeat steps 2 thru 3.

DO NOT operate an electric starter for more than 5 seconds
each attempt.

4. When engine starts:

a. Release starter button or ignition switch key.
b. Next, move combined

control to “FAST”.

c. Finally, move combined

control to desired speed in

“RUN” range.

NOTES

If engine starts, but falters when combined control is moved
to “FAST” position:

a. Momentarily move combined control back to

“CHOKE” position.

b. Next, move combined control to “FAST” position.
c. Finally, move combined control to desired speed in

“RUN” range.

If engine dies after combined control is moved to “FAST”
position, repeat steps 2 thru 4 to restart engine.

5. If engine fires but does not continue to run, move com-

bined control lever to “FAST” position and then start
engine.

6. If engine fails to start after 3 attempts with combined

control in “FAST” position, move control to “CHOKE”
position and push button or turn key to start engine
again.

7. If engine does not start after following steps 1 thru 6,

contact your Authorized Tecumseh Servicing Dealer.
DO NOT attempt to start or troubleshoot this engine in
any other way.

Table 3. Engine Sections with Electric Starters

If your engine has:

Go to:

Combined Speed and Choke Controls Section A.I

Independent Speed and Choke
Controls

Section A.II

!

WARNING

!

WARNING

Figure 8. Combined Speed and Choke Control

Figure 9. Typical Engine Symbols

STOP

STOP

SLOW

RUN

FAST CHOKE

«
...
32
33
34
35
36
...
»

Содержание LT 542H

















































Отзывы:

Нет отзывов

Похожие инструкции для LT 542H

Бренд: Walker Страницы: 72

Бренд: Snapper Страницы: 40

Бренд: Hayter Страницы: 56

Бренд: Ariens Страницы: 29

Бренд: EGO Страницы: 444

Бренд: Flymo Страницы: 80

Бренд: GreenWorks Страницы: 164

Бренд: Agri-Fab Страницы: 16

Бренд: Grizzly Страницы: 96

Бренд: Bad Boy Страницы: 48

Бренд: Toro Страницы: 48

Бренд: Cub Cadet Страницы: 24

Z-Force S Commercial 60

Бренд: Cub Cadet Страницы: 40

Бренд: Gude Страницы: 92

Бренд: Fieldmann Страницы: 21

Бренд: Jonsered Страницы: 56

Бренд: Wolf Garten Страницы: 289

BERTOLINI 130 S

Бренд: EMAK Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды