manualshive.com logo in svg

White Outdoor LT-1650, Руководство оператора

Поделиться
Скачать
White Outdoor LT-1650 Скачать руководство пользователя страница 17

17

•

Looking at the transmission from the right side of 
the tractor, locate the compression spring and 
brake disc. See Figure 10.

Figure 10

•

Carefully remove the cotter pin from the crown nut 
on the right side of the brake assembly.

•

Using a feeler gauge, check the gap between the 
brake disc and the brake puck. Proper gap is .011". 

•

Tighten the crown nut until the proper gap is 
achieved.

•

Insert a replacement cotter pin (part number 714-
0111) into the crown nut.

Steering Adjustment

If the tractor turns tighter in one direction than the other, 
or if the ball joints are being replaced due to damage or 
wear, the steering drag links may need to be adjusted.

Adjust the drag links so that equal lengths are threaded 
into the ball joint on the left side and the ball joint on the 
right side:

•

Loosen the jam nut found on the drag link at the 
rear of the ball joint. See Figure 11.

•

Remove the hex nut and lock washer on the top of 
ball joint. See Figure 11.

Figure 11

•

Thread the ball joint toward the jam nut to shorten 
the drag link. Thread the ball joint away from the 
jam nut to lengthen the drag link.

•

Replace hex nut and lock washer and retighten the 
jam nut after proper adjustment is achieved.

NOTE: 

Threading the ball joints too far onto the drag

links will cause the front tires to "toe-in" too far. Proper
toe-in is between 1/16" and 5/16".

Front tire toe-in can be measured as follows:

•

Place the steering wheel in position for straight 
ahead travel.

•

In front of the axle, measure the distance 
horizontally from the inside of the left rim to the 
inside of the right rim. Note the distance.

•

Behind the axle, measure the distance horizontally 
from the inside of the left rim to the inside of the 
right rim. Note the distance.

•

The measurement taken in front of the axle should 
be between 1/16" and 5/16" less than the 
measurement taken behind the axle.

•

Adjust if necessary.

SECTION 7:  MAINTAINING YOUR LAWN TRACTOR

WARNING: 

Before performing any

maintenance or repairs, disengage PTO,
move shift lever into neutral position, set
parking brake, stop engine and remove key to
prevent unintended starting.

Cleaning the Engine And Deck

Any fuel or oil spilled on the machine should be wiped 
off promptly. 

Do NOT allow debris to accumulate around the cooling 
fins of the engine or on any other part of the machine, 
especially the belts and pulleys.

IMPORTANT:

 The use of a pressure washer or garden 

hose to clean your tractor is NOT recommended. It may 
cause damage to electrical components, spindles, 
pulleys, bearings or the engine. The use of water will 
result in a shortened life of the tractor and reduce its 
serviceability.

Brake Disc

Crown Nut

NOTE:

 

View shown from beneath tractor. 

Hydrostatic

Transmission

Brake Rod

Drag Link

Ball Joint

Axle

Pivot Bar

Hex Nut and

Jam Nut

Lock Washer

Содержание LT-1650













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды