background image

25233-0-0109

Page 12

cAuTION: ALL wIrINg ShOuLD Be DONe By A QuALIFIeD eLecTrIcIAN AND ShALL Be IN cOMpLIANce 

wITh ALL LOcAL, cITy AND STATe BuILDINg cODeS. BeFOre MAKINg The eLecTrIcAL cONNecTION, 

MAKe Sure ThAT MAIN pOwer SuppLy IS DIScONNecTeD. The AppLIANce, wheN INSTALLeD, MuST Be 

eLecTrIcALLy grOuNDeD IN AccOrDANce wITh LOcAL cODeS Or, IN The ABSeNce OF LOcAL cODeS, 

wITh The NATIONAL eLecTrIcAL cODe ANSI/NFpA 70 (LATeST eDITION)

a factory installed junction box is located on the lower right 

hand side of the firebox. Wiring must be fed to the junction 

box and attached to the receptacle that is provided. Remove the 

knockout in the installed junction box to accept wiring into the 

junction box. install a UL listed cable clamp (not supplied) in the 

knockout hole. Leave approximately 6" of wire in the junction 

box for connection.
attach black wire to one side of the receptacle and white wire to 

opposite side of receptacle. the ground wire should be attached 

to the green (neutral) screw.
install the receptacle into the junction box. attach cover plate.

Keep the control compartment, logs and burner area surrounding the 

logs clean by vacuuming or brushing area at least twice a year.
tHE LogS can gEt VERY Hot – HanDLE onLY WHEn 

cooL.
always turn off gas to the pilot before cleaning. For relighting, 

refer to lighting instructions located on the log set.

Never obstruct the flow of the combustion and ventilation air. Keep 

the front of the firebox clear of all obstacles and materials.

Screens must be closed during operation.

Figure 20

JUnction BoX WiRing inStaLLation inStRUctionS

MaintEnancE

INDex 

NO.

pArT NuMBer.

DeScrIpTION

VFS32FB2DF

VFS32FB3DF

VFS32FB2eF

VFS32FB3eF

1

17247

17247

17247

17247

toP StanDoFF

2

10554

10554

10554

10554

FRaMing BRacKEt

3

17162

17162

17162

17162

JUnction BoX aSSEMBLY

4

R3492

R3492

R3492

R3492

Receptacle

5

R3491

R3491

R3491

R3491

coVER, JUnction BoX

6

19945

19945

19945

19945

BRacKEt, toP BRicK REtainER 

7

R8667

R8667

R9422

R9422

BRicK PanEL RigHt

8

BRicK PanEL BacK

9

BRicK PanEL LEFt

10

20020

20020

20020

20020

HooD

11

R7051

R7051

R7051

R7051

RoD, ScREEn

12

R8213

R8213

R8213

R8213

ScREEn cURtain

13

19401

19401

19401

19401

BRacKEt, BottoM BRicK REtainER

14

R9292

R9292

R9292

R9292

HEaRtH LEDgE, RigHt

15

R9293

R9293

R9293

R9293

HEaRtH LEDgE, LEFt

16

R9294

R9294

R9294

R9294

HEaRtH LEDgE, cEntER

17

23004

23004

23004

23004

REtainER, HEaRtH LEDgE

PaRtS LiSt

Содержание FS36FB3EF-3

















Отзывы: