manualshive.com logo in svg

Whisper Power 61242040, Руководство пользователя

Поделиться
Скачать
Whisper Power 61242040 Скачать руководство пользователя страница 27

      

WhisperPower Inverter / Battery Charger

         

27

Understanding the Error Codes

Code

Condition

Corrective Action

E01

(Battery 

Mode)

No AC Output. Inverter shutdown due to 

low 

battery

 voltage. 

Recharge the battery immediately and restart 
unit. 

Note: E01 will shows for about 30 sec. After 30 sec, Display will turns Off and unit will shutdown completely.

E01

(By-Pass 

Mode)

- No battery is connected to the unit.

- Check the battery connection.

- Battery voltage remains < 19.0V. A large portion 

of the charger current provided is used to 
maintain the DC load connected to the battery. 
E01 will turn OFF when the battery voltage is 
charged to > 19.0V

- Remove or turn off DC load connected to 

the battery to minimize the charging time to 
charge the battery to > 19.0V. If this condition is 
ignored, the charger will terminate the charging 
process (See note below).

Note: The charger current with battery voltage < 9.5V is limited to ~25A and there is a 15 minute timer 
to allow the charger to charge the battery to > 9.5V. If battery voltage remains < 9.5V after 15 minutes of 
charge, the charger will shutdown and show E11 (Bad battery). 

E02

When unit is in Battery/Inverter mode, unit senses 
the 

battery voltage is too high

 and inverter has 

shutdown.

Check battery voltage or determine if any 
external charger is connected to the battery bank 
that leads to high battery voltage.

E03

When unit is in Battery/Inverter mode, 

AC output 

is overloaded 

or short-circuited and inverter has 

shutdown.

Check load connected to the output. Reduce 
load and restart the unit.

Note: E03 will shows for about 30 seconds. After 30 seconds, Display will turns Off and unit will shutdown 
completely.

E04

When unit is in Battery/Inverter mode, Internal 

temperature is too high

 and inverter has 

shutdown.

Turn unit off and wait for 15 minutes before 
restarting. Check if any object has blocked the 
airflow of the unit.

E05

When unit is in Battery/Inverter mode Input 

battery voltage is low

 and warning occurs.

Recharge battery as unit will shutdown shortly.

E06

When unit is in Battery/Inverter mode AC 

output 

load

 connected has been sensed high and is 

close to shutdown limit.

Reduce AC load.
Note: E06 occurs when AC Output power is 
close to 1850W for 2000W units and 2800W for 
3000W unit. 

E07

When unit is in Batter/Inverter mode Internal 

temperature is high

 and is close to over-

temperature shutdown limit.

Reduce load and check if any ventilation of the 
unit is blocked.

E10

When unit is in By-Pass mode, 

Battery Charging 

voltage too high.

Check battery setting. Check and any other DC 
power sources connected to the battery has high 
voltage. 

Содержание 61242040





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды