manualshive.com logo in svg

WHISPER KOOL Mini Split, Техническое руководство, Страница: 7 / 36

Поделиться
Скачать
WHISPER KOOL Mini Split Скачать руководство пользователя страница 7

www.whisperkool.com | Page 5

RECEIVING & INSPECTING THE SYSTEM

Please leave the unit in its original box until you are ready for installation.  This will allow you to move the product 

safely without damaging it.  When you are ready to remove the product from the box, refer to the installation 

instructions. 

TIP:

  Save your box and all packaging materials.  They provide the only safe means of transporting/shipping the unit. 

(1) Platinum Mini Split Evaporator Unit ( Fan Coil Unit)

(1) Condensing Unit

(1) 12 Foot Bottle Probe

(4) 2” #8 Hex Head Screws

(1) 10 FT. 1/2”Drain Line

(1) ¼” Sight Glass

(1) ¼” Filter Drier

(1) Power Cord Strain Relief (located 

inside the Evaporator Unit)

(1) Split System Warranty Checklist

(1) 10” Piece of Cork Tape

(1) Split System Owner’s Manual

(1) Split System Tech Manual 

(1) Evaporator Mounting Template

Main Evaporator Box

Main Condensing Unit Box:

°

F

Receiving and Inspecting the System 

• 

Lift only at the designated hand hold locations on the shipping container or fully support the unit from 

underneath. A shipment may include one or more boxes containing accessories. 

• 

Before opening the container, inspect the packaging for any obvious signs of damage or mishandling.  

• 

Write any discrepancy or visual damage on the Bill of Lading before signing. 

• 

Allow the condensing unit to sit 24 hours prior to start up. The Condensing Unit can be placed in the 

installation location, piped and evacuated during this time.

Note:

 WhisperKOOL units are manufactured in the USA and tested prior to shipment. 

Review the Packing Slip to Verify Contents

• 

Check the model number to ensure it is correct. 

• 

Check that all factory options ordered are listed. 

If any items listed on the packing slip do not match your order information,

contact WhisperKOOL Customer Service immediately. 

Check the Box for the following contents:

 

Содержание Mini Split





































Отзывы:

Нет отзывов