background image

3.

4.

Alternately, you can write to Yakima at 17 Hinkler Court, Brendale QLD Australia 4500 in order to make a claim under your
warranty.

 
Upon contacting Yakima directly, you should explain as fully as possible the defect. A Yakima representative will provide you
with appropriate instructions for returning the product together with a copy of the original purchase invoice or receipt to
Yakima.

 
The costs and expenses associated with making a claim under your warranty including the costs of complying with those
instructions and of returning the product to Yakima or the Whispbar dealer will be borne by you.

 

 
Following receipt of the product and purchase invoice or receipt, Yakima or the Whispbar dealer must inspect the product to
determine whether the claim falls within the warranty. If:

 

 
4.1 the claim falls within the warranty, Yakima will remedy any defects in materials or workmanship becoming apparent during the
warranty period, by replacing or repairing any defective product or component (at its option) free of charge to the purchaser in
respect of replacement parts or labour.

 
4.2 the claim does not fall within the warranty, Yakima will return the product to you at your expense.

 

Fitting Kit

EN

K556W

13

Содержание K556W














Отзывы: