4
■
To add rinse aid, open the dispenser lid by gently pushing in the
center of the lid with your thumb while lifting up on the edge.
■
Pour rinse aid into the opening until the indicator level shows that it
is full.
■
Close dispenser by pushing down gently on the lid.
NOTE:
For most water conditions, the factory setting will
give good results.
If you are experiencing poor drying performance, you may
want to try a higher setting. Turn the arrow adjuster to a
higher setting to increase the amount of rinse aid.
5.
Select a Cycle (cycles vary by model)
Efficient dishwashers run longer to save water and energy, just as
driving a car slower saves on gas. Typical cycle time is approximately
2
¹⁄₂
hours but can take less or more time to complete depending on
selections.
6.
Select Options (options vary by model)
You can customize your cycles by pressing the options desired. If you
change your mind, press the option again to turn off the option. Not all
options are available for every cycle. If an invalid option is selected for a
given cycle, the lights will flash. Adding options may increase the cycle
time displayed.
7.
Follow the Progress of your Dishwasher
The full lit display will glow for wash, drain,
drying, sanitized, and complete. It will also
display the remaining time for the cycle in
hours and minutes.
Select the desired cycle by pressing the
Cycles button. Each time the cycles button is pressed the next available
cycle will be displayed.
8.
Start or Resume a Cycle
NOTE:
Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water.
■
If the Start/Resume button is located on top of door; push door
firmly closed within 3 seconds of pressing Start/Resume. If door is
not closed within 3 seconds, the start button LED will flash, an
audible tone will be heard and cycle will not start.
IMPORTANT:
If anyone opens the door (such as, for adding a dish,
even during the Delay Hours option), the Start/Resume button must
be pressed each time.
■
If your Start/Resume button is located on front of door; push door
firmly closed. The door latches automatically. Select the wash
cycle, options and press START/RESUME or press
START/RESUME to repeat the same cycle and options as in
previous wash cycle.
This information covers several different models. Your dishwasher may not have all of the cycles and options described. Estimated cycle times
may increase or decrease depending on water temperature, soil conditions, dish load size, and options selected.
Pre W
ash
OPEN
SLIDE
SLIDE
Full
Add
CYCLES
ESTIMATED
WASH TIME
DISPLAYED*
H:MM
W/O OPTIONS
WATER USAGE
GALLONS
(LITERS)
The most advanced and versatile cycle. This cycle senses soil amount and toughness of
soil to adjust the cycle for improved performance using only the amount of water and
energy needed. Use for all soil levels.
2:30
3.38 to 7.4
(12.8 to 28.0)
Use for hard-to-clean, heavily soiled pots, pans, casseroles, and tableware.
3:28
7.4
(28.1)
This cycle with only the Heated Dry option selected, and without other options selected,
is recommended to completely wash and dry a full load of normally soiled dishes. The
energy usage label is based on this cycle and option combination.
2:32
2.4 to 7.4
(9.09 to 28)
For fast results, 1- Hour Wash will clean dishes using more water and energy. Select the
Heat Dry option to provide best dry performance. May be used for all soil levels.
1:00
7.87 (29.8)
This cycle quietly soaks dishes with an extended prewash which eliminates the need to
presoak dishes saving personal time and effort. For optimal cleaning results during the
Soak & Clean cycle add prewash detergent. Use this cycle for loads with heavy amounts
of dried on or hard to clean baked-on food.
7:31
7.4 (28.0)
CYCLE GUIDE
