background image

8

Door Closing and Alignment

Door Closing

Your refrigerator has two front adjustable rollers – one on the right 
and one on the left. If your refrigerator seems unsteady or you 
want the doors to close easier,

 

adjust the refrigerator's tilt using 

the instructions below:

1.

Plug into a grounded 3 prong outlet. 

2.

Move the refrigerator into its final position. 

3.

Remove the base grille (see “Base Grille” earlier in this 
section). The two leveling screws are part of the front roller 
assemblies which are at the base of the refrigerator on either 
side.

4.

Use a screwdriver to adjust the leveling screws. Turn the 
leveling screw to the right to raise that side of the refrigerator 
or turn the leveling screw to the left to lower that side. It may 
take several turns of the leveling screws to adjust the tilt of 
the refrigerator. 

NOTE:

 Having someone push against the top of the 

refrigerator takes some weight off the leveling screws and 
rollers. This makes it easier to adjust the screws.

5.

Open both doors again and check to make sure that they 
close as easily as you like. If not, tilt the refrigerator slightly 
more to the rear by turning both leveling screws to the right. It 
may take several more turns, and you should turn both 
leveling screws the same amount.

6.

Replace the base grille.

Door Alignment

If the space between your doors looks uneven, you can adjust it 
using the instructions below:

1.

Pry off the top hinge cover.

2.

Loosen the top hinge screws using a 

⁵⁄₁₆

 in. socket or wrench.

3.

Have someone hold the door in place or put a spacer 
between the doors while you tighten the top hinge screws.

4.

Replace the top hinge cover.

Understanding Sounds You May Hear

Your new refrigerator may make sounds that your old one didn’t 
make. Because the sounds are new to you, you might be 
concerned about them. Most of the new sounds are normal. Hard 
surfaces, like the floor, walls, and cabinets, can make the sounds 
seem louder than they actually are. The following describes the 
kinds of sounds and what may be making them.

If

 

your product is equipped with an ice maker, you will hear a 

buzzing sound when the water valve opens to fill the ice 
maker for each cycle.

The defrost timer will click when the automatic defrost cycle 
begins and ends. Also, the Thermostat Control (or 
Refrigerator Control depending on the model) will click when 
cycling on and off.

Rattling noises may come from the flow of refrigerant, the 
water line, or items stored on top of the refrigerator.

Your refrigerator is designed to run more efficiently to keep 
your food items at the desired temperature. The high 
efficiency compressor may cause your new refrigerator to run 
longer than your old one, and you may hear a pulsating or 
high-pitched sound.

Water dripping on the defrost heater during a defrost cycle 
may cause a sizzling sound.

You may hear the evaporator fan motor circulating the air 
through the refrigerator and freezer compartments.

As each cycle ends, you may hear a gurgling sound due to 
the refrigerant flowing in your refrigerator.

Contraction and expansion of the inside walls may cause a 
popping noise.

You may hear air being forced over the condenser by the 
condenser fan.

You may hear water running into the drain pan during the 
defrost cycle.

USING YOUR 

REFRIGERATOR

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit 
airflow between the refrigerator and freezer sections. As shown in 
the illustration, cool air enters through the bottom of the freezer 
section and moves up. Most of the air then flows through the 
freezer section vents and recirculates under the freezer floor. The 
rest of the air enters the refrigerator section through the top vent.

Do not block any of these vents

 with food packages. If the 

vents are blocked, airflow will be prevented and temperature and 
moisture problems may occur.

IMPORTANT:

 Because air circulates between both sections, any 

odors formed in one section will transfer to the other. You must 
thoroughly clean both sections to eliminate odors. To prevent 
odor transfer and drying out of food, wrap or cover foods tightly.

Содержание ST18PKXJW00





















Отзывы: