Whirlpool M-17 Скачать руководство пользователя страница 7

Страница: 7 / 88

GENERAL INFORMATION (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

1-3

General Theory of Operation

Maytag

Microfiltration Wash System

No Filter Cup, No Chopper

The industry’s first microfiltration system is a clear departure

from traditional, passive filtration because it continuously

filters 100% of the water, reducing the cycle time and energy

consumption on the heaviest loads.
Similar on the Surface, Radically Different Inside
The only visible filtration component of the new filtration system

is the coarse filter in the bottom of the tub. The rest of the high-

performance filtration system is below the tub.

How Microfiltration Works

Water and food particles flow through the coarse filter into

the filter housing.

An impeller pulls wash and rinse water into the spinning

ultra-fine filter.

The ultra-fine filter is cleaned by an area of back-pressure

created by two sets of wing-shaped blades located inside and

outside the filter.

Food particles remain suspended inside the filter housing;

filtered water is pumped back to the wash arms.

During draining, a secondary pump flushes out food particles

and soils.

A. Outer Blades

B. Inner Blades

Area of Back Pressure

Wash Flow
Drain Flow

Wash

Motor

Dirty

Water

Enters

Drain

Motor

Food Soils

Flushed Out

Impeller

Содержание M-17

























































































Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды

Whirlpool M-17, Техническое руководство

Результаты поиска

Содержание M-17

Отзывы:

Похожие инструкции для M-17

Бренды по названию

Популярные бренды