GB17
Before starting the installation procedure open the perimeter suction panels and remove the grease filter/s, the carbon filter frame (if installed), following the
procedures described in the appropriate maintenance sections.
The instructions below, in number sequence, refer to the drawing shown in the following page, numbered accordingly.
FIG. 1
1
The height of the hood can be adjusted by adjusting the extension of the hood supporting structure. Keep in mind that upon completion of the installation,
the minimum distance between the hood and the hob must be in accordance with the requirements listed in this booklet.
2.
Fix the two sections of the structure using a total of 16 screws (4 for each corner).
Reinforce the upper section, if extending over the minimum length, by fitting 1 or 2 brackets (according to what included). Do this following the procedure
below:
a.
Slightly widen the brackets to be fitted, so that they can be secured to the outside of the structure.
b.
Place the reinforcing bracket immediately above the fixing point of the two sections of the structure and secure using 8 screws (2 for each corner).
If supplied, fit the second reinforcing bracket at equal distance between the first reinforcing bracket and the top of the lattice-work. Secure using 8 screws
(2 for each corner).
Note:
when positioning and securing the reinforcing bracket/s ensure that they leave the necessary room for the discharge tube (suction version), or the
deflector (filter version), to be fitted comfortably.
3.
Position the drilling template on the ceiling right above the hood (the centre of the drilling template must correspond to the centre of the hob, and the sides
must be parallel to the sides of the hob). The side of the template with FRONT corresponds to the control panel side).
Fit the electric connections.
4.
Drill the holes as shown (6 holes for 6 wall plugs - 4 plugs for hooking), fit the 4 screws to the external holes and tighten, leaving a space of approximately 1
cm between the screw and the ceiling.
5.
Fit the discharge tube inside the lattice-work and connect to the fitting ring of the motor compartment (discharge tube and fixing collars not supplied).
6.
Hook the lattice-work to the 4 screws (see operation
4
).
IMPORTANT:
The side of the lattice-work with the connection box corresponds to the side of the control panel when the hood is installed.
7.
Fully tighten the 4 screws.
8.
Insert and fully tighten the other 2 screws to the remaining safety fixing holes.
9.
Connect the hood to the mains; the electric supply line must be powered only when the installation has been completed.
10.
Hook the hood to the lattice-work, ensuring correct positioning - to hook the hood to the lattice-work, partially tighten the 4 screws (also see operation
12
).
11.
Fit the hood to the lattice-work with two screws. These will also be needed to centre the two parts.
12.
Fully tighten the 4 screws securing the lattice-work to the hood.
FIG. 2
13.
For the suction version (
13A
), connect the other end of the discharge pipe to the discharge outlet of the home.
For the filter version (
13F
), fit the deflector F to the lattice-work and secure to its bracket with 4 screws. Connect the discharge pipe to the connection ring
on the deflector.
14.
Fit the nuts with hooks inside the sections of the upper and lower chimneys, by the rectangular holes; 14 nuts in total must be fitted.
15.
Couple the two upper sections of the chimney, covering the lattice-work so that the air vents on the two sections are one on the side on the control panel,
and the other on the opposite side.
Secure the 2 sections using 8 screws (4 for each side - see the diagram for the coupling of the two sections).
16.
Secure the lattice-work to the upper chimney assembly, near the ceiling, using two screws (one for each side).
Refit the carbon filter holding frame and the grease filter/s.
FIG. 3
17
Complete the electric connection of the control panel and the lamps.
18.
Couple the two bottom section of the chimney, covering the lattice-work, using 6 screws (3 for each side - see the diagram for the coupling of the two
sections).
19.
Insert the bottom section of the chimney in the appropriate seat, fully covering the motor compartment and electric connection box. Secure with two screws
(some models only), from the inside of the hood.
20.
Fit the 2 cover plates (supplied, and recognisable from the hooks).
The wider, deeper, cover plates are for the upper chimney, and must be cut to size.
INSTALLATION - ASSEMBLY INSTRUCTIONS
Содержание Hood
Страница 8: ...GB19 ...
Страница 9: ...GB20 ...
