Page 3
Recommended
ground method
For personal safety, this range is equipped with a
power supply cord having a 3-prong ground
plug. To minimize possible shock hazard, the
cord must be plugged into a mating 3-prong,
ground-type outlet, grounded in accordance with
the National Electrical Code, ANSI/NFPA 70 —
latest edition* and all local codes and
ordinances.
If a mating outlet is not available, it is the
personal responsibility and obligation of the
customer to have a properly polarized and
grounded, 3-prong outlet installed by a qualified
electrician.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts, 02269
Electrical requirements
Gas supply requirements
Observe all governing codes and ordinances.
This installation must conform with local codes
and ordinances.
In the absence of local codes,
installations must conform with American
National Standard, National Fuel Gas Code ANSI
Z223.1 — latest edition**.
Input ratings
shown on the model/serial rating
plate are for elevations up to 2,000 feet. For
assistance when installing the range at higher
elevations, contact your local service company.
Type of gas:
This range is design-certified by
CSA International for use with Natural gas or,
after proper conversion, for use with L. P. gas.
This range is factory set for use with Natural gas.
Gas conversion instructions are provided on
pages 7-8. The model/serial rating plate located
on the frame behind the storage drawer or
broiler door has information on the type of gas
that can be used. If the type of gas listed does
not agree with the type of gas available, check
with the local gas supplier.
Conversion must be
done by a qualified service technician.
Gas supply line:
Provide a gas supply line of 3/4"
rigid pipe to the range location. With L.P. gas,
piping or tubing size can be 1/2" minimum. A
smaller size pipe on longer runs may result in
insufficient gas supply. Usually, L.P. gas
suppliers determine the size and materials used
in the system.
Pipe-joint compounds
made for use with L.P. gas
must be used on pipe threads only.
Flexible metal appliance connector:
If local codes
permit, a new AGA or CSA design-certified, 1/2"
or 3/4" I.D., flexible metal appliance connector is
recommended for connecting range to the gas
supply line. A 1/2" male pipe thread nipple is
needed for connection to pressure regulator
female pipe threads.
Do Not kink or damage the
flexible metal tubing when moving the range.
Shutoff valve:
The supply line must be equipped
with a manual shutoff valve. This valve should be
located in the same room as the range and
should be in a location that allows ease of
opening and closing. The valve is for turning on
or shutting off gas to the range.
Do Not block
access to shutoff valve.
Pressure regulator:
The gas pressure regulator
supplied with this range must be used. The inlet
pressure to the regulator should be as follows for
proper operation:
NATURAL GAS:
Minimum pressure: 5 inches W.C.
Maximum pressure: 14 inches W.C.
L.P. GAS:
Minimum pressure: 11 inches W.C.
Maximum pressure: 14 inches W.C.
Contact local gas supplier if you are not sure
about the inlet pressure.
Line pressure testing above 1/2 psi gauge
(14" WCP) —
The range and its individual manual
shutoff valve must be disconnected
from the gas supply piping system during any
pressure testing of that system at test pressures
greater than 1/2 psig (3.5 kPa).
Line pressure testing at 1/2 psi gauge
(14" WCP) or lower —
The range must be
isolated from the gas supply piping system by
closing its individual manual shutoff valve during
any pressure testing of that system at test
pressures equal to or less than 1/2 psig (3.5 kPa).
Copies of the standards listed may be obtained from:
** CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
manual shutoff valve
“open” position
gas supply
to range
Rigid pipe connection:
Requires a
combination of pipe fittings to obtain
an in-line connection to the range. All
strains must be removed from the
supply and fuel lines so range will
be level and in line.
3-prong properly polarized
ground-type outlet
3-prong ground
plug
ground
prong
power supply
cord
level
flat-blade
screwdriver
stainless
steel/glass
mirror
tape measure
or ruler
safety glasses
gloves
hand or
electric drill
wood floor:
1/8" drill bit
concrete/ceramic floors:
3/16" carbide-tipped masonry
drill bit (Hammer may be
needed for anchors.)
Materials required:
• gas line shutoff valve
• 1/2" male pipe thread nipple for connection to pressure
regulator
• L.P. gas-resistant pipe-joint compound
• AGA or CSA design-certified flexible metal appliance
connector (4-5 feet) or rigid gas supply line as needed
• Insulated pad or 1/4" plywood if range is installed
over carpeting
Tools needed
channel lock
pliers
15/16"
and 3/8"
combination
wrenches
pipe
wrench
3/8" drive
ratchet
Phillips
screwdriver
If codes permit and a separate ground wire is
used, it is recommended that a qualified
electrician determine that the ground path is
adequate and that the outlet is correctly
polarized.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not
sure range is properly grounded.
A 120-volt, 60-Hz, AC-only, 10-ampere, fused
electrical supply is required. A time-delay fuse or
circuit breaker is recommended. It is
recommended that a separate circuit serving
only this appliance be provided.
Electronic ignition systems operate within wide
voltage limits, but proper grounding and polarity
are necessary. In addition to checking that the
outlet is correctly grounded, the outlet must be
checked by a qualified electrician to see if it is
wired with correct polarity.
Important:
This range is equipped with an
electronic ignition system that will not operate if
plugged into an outlet that is not properly
polarized.
A wiring diagram is included on the back of
the range.
See “Cabinet dimensions/requirements,” Page 2,
for recommended location of electrical outlet.
putty knife
Electrical Shock Hazard
Plug into a grounded 3-prong outlet.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these instructions can
result in death, fire, or electrical shock.
WARNING
Explosion Hazard
Use a new AGA or CSA approved gas supply
line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person
make sure gas pressure does not exceed
14" water column. Examples of a qualified
person include licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death,
explosion, or fire.
WARNING
