Whirlpool Gold WFD195 Скачать руководство пользователя страница 42

Страница: 42 / 48

BLOWER PERFORMANCE DATA

■

Normal furnace
operation.

■

Integrated
control module
diagnostic LED
is flashing
7 flashes.

7 flashes

■

Flame sense
microamp signal
is low.

■

Flame sensor is coated/
oxidized.

■

Flame sensor incorrectly
positioned in burner
flame.

■

Lazy burner flame due to
improper gas pressure
or combustion air.

■

Sand flame sensor if
coated/oxidized.

■

Inspect for proper
sensor alignment.

■

Compare current gas
pressure to rating plate
info. Adjust as needed.

■

Turn off power
prior to repair.

■

Sand flame
sensor with
emery cloth.

■

See “Vent/Flue
Pipe” section for
piping details.

■

See rating plate
for proper gas
pressure.

■

No furnace
operation

■

Integrated
control module
diagnostic LED
is flashing
8 flashes.

8 flashes

■

Problem with
igniter circuit.

■

Improperly connected
igniter.

■

Bad igniter.

■

Poor unit ground.

■

Poor burner ground.

■

Faulty integrated control
module.

■

Check and correct
wiring from integrated
control module to
igniter

■

Replace bad igniter.

■

Check and correct
furnace ground wiring

■

Replace faulty
integrated control
module.

■

Turn off power
prior to repair.

■

Replace igniter
with correct
replacement part.

■

Replace
integrated control
module with
correct
replacement part.

■

Read precautions
in “Electrostatic
Discharge”
section of
manual.

■

Induced draft
blower runs
continuously.
No furnace
operation.

■

Integrated
control module
diagnostic LED
is flashing
continuously.

Continuous

flashes

■

Polarity of 115-
volt or 24-volt
power is
reversed.

■

Polarity of 115-volt AC
power to furnace or
integrated control
module is reversed.

■

Red and blue wires to
transformer are
reversed.

■

Poor unit ground.

■

Review wiring diagram
to correct polarity.

■

Verify proper ground.
Correct if necessary.

■

Reverse red and blue
wires connected to
transformer.

■

Turn off power
prior to repair.

Symptoms of
Abnormal
Operation

Associated
LED Code

Fault Description Possible Causes

Corrective Actions

Notes and
Cautions

Blower Performance Data

CFM and Temperature Rise vs. External Static Pressure

Model—Heating
Speed as Shipped

Motor
Speed

Tons
AC at
0.5"
ESP

External Static Pressure (Inches Water Column)

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

CFM

Rise CFM

Rise CFM CFM CFM

WGFM1950453BXA
(MED-HI)

High

3.0

1,352

1,318

1,260

1,202

1,128

1,044 955

853

Med

2.5

1,214

1,172

1,123

1,064

1,012

938

859

741

Med-Lo

2.0

997

994

960

923

884

817

741

611

Low

1.5

757

753

734

704

674

620

524

438

WGFM1950703BXA
(MED-HI)

High

3.0

1,449

1,409

1,326

1,273

1,201

1,194 1,136 1,018

Med

2.5

1,192

1,172

1,141

1,094

1,046

973

904

793

Med-Lo

2.0

981

962

943

917

888

830

764

665

Low

1.5

750

730

714

692

657

620

570

502

Содержание Gold WFD195

















































Результаты поиска

Содержание Gold WFD195

Отзывы:

Whirlpool Gold WFD195, Руководство по установке, Страница: 42 / 48

Результаты поиска

Содержание Gold WFD195

Отзывы: