INSTALLATION MANUAL
INSTALLATION MANUAL
AUTOMATIC
W
ASHER
We congratulate you for your choise. In order to certify the good performance of your Washer, and improve
its life please, follow these instructions.
CHECKING THE INSTALLATION REQUIREMENTS
INSTALLING THE WASHER
TURNING THE WASHER ON
CHECKING THE INSTALLATION REQUIREMENTS
INSTALLING THE WASHER
TURNING THE WASHER ON
Check the
supply
voltage
indicated
on the
label
attached to the
Washer’s power cord,
and see if the power
outlet that will be used
for the connection has
the same voltage(120V)
You must install your Washer:
In a location that is not exposed to
direct sunshine or rain.
Warranty and Autorized Service List.
On a flat, level surface, with
adequate support for all feet. This
will help to avoid vibration, noise
and leakage (see how to level your
Washer on iten 3).
2. Remove the bottom
packagingpiece by lifting
it by the side handles.
Never use the Washer
with the bottom packaging
piece under the machine,
as you may damage it.
47
inches
34
inches
Set the curve of the water outlet
rubber hose in the tank, or in a
exclusive draining tube .
Set the Washer in
its location,
installing it 10cm
away from the
wall, furniture, or
other objects.
In order to check if
your Washer is
adequately
laveled, fill it with
water up to the
MIDDLE LEVEL and
see if the water
surface is perfectly
aligned with the
basket holes.
Please note inside the threaded part the sealing washer
with filter-screen, which must be with the prominent side
of the filter-screen turned outwards.
Connect the hose on the tap, sufficiently tight to avoid
water leakage. Open the tap and ckeck if there is leakage in
either end and . In case that occurs, tighten again the
connections and .
Do not use plug adapters, extensio cords or improvised connections between the
Washer and the wall outlet. If there is more than one home appliance connected in
the same outlet, there is the risk of a surge and damage may occur to the products.
Ckeck if all the recommendations in the sections 1, 2 and 3 were followed.
Check if the tap and the shutoff valve are open.
Connect the Washer’s power cord to the power outlet.
4. Remove the film that
protects the control
panel.
Thermal cut-outs or
fuses are required for
the Washer protection.
ELETRIC REQUIREMENTS
INSTALL THE WATER OUTLET RUBBER HOSE
USE THE ADJUSTABLE FEET
TO LEVEL YOUR WASHER
INSTALL THE WATER INLET HOSE
LOCATION FOR INSTALLATION
CHECK THE ACESSORIES
The water pressure
needed filling the Washer
should correspond to a
level of 6ft to 260ft above
the tap (approximately
0,3 PSI to 11 PSI)
WATER REQUIREMENTS
ATENTION
IMPORTANT:
IMPORTANT:
IMPORTANT:
IMPORTANT:
If there are no
thermal cut-outs in
the power
distribution panel,
and a exclusive
tripolar power outlet
is not available, seek the aid of an
electrician to install them
(preferably in some place near the
Washer).
Never change the power cord or use it
differently from recommended. If
installation or repair is necessary, call
in an authorized service technician.
The curved end of the water outlet hose must be located between
34 inches and 47 inches. If below34 inches your Washer will not
reach the water level considered adequate for operation. If located
above 47 inches, the Washer will not be able to drain the water.
The filter-screen in that position prevents dirt present
in the water from blocking the filter. Occassionally, it may be
necessary to disconnect the hose from the tap and clean the
filter-screen with a brush and water.
Don’t conect the Washer hot water inlet to a water source
with temperature above 140F.
Your Washer was designer with
adjustable feet, which are useful
for the leveling and stability of
the product.
The wide diameter of the electric
network must conform to the following
table:
Distance
from panel
Gauge
99 to 164ft
6#AWG
120V
12#AWG
30ft to 39ft
10#AWG
40ft to 65ft
8#AWG
66 to 98ft
WATER CONSUPTION
GENERAL
Centrifugation (rpm)
750
WITHOUT PACKAGE
WITH SHRINK PACKAGE
High Level
Medium Level
Program
215 liters
149 liters
Super Wash
215 liters
149 liters
Regular Wash
175 liters
129 liters
Fast Wash
SIZE AND WEIGHT
22’’
24’’
26’’
41’’
25’’
39’’
Width
Depth
Height with the lid closed
75 lbs
79 lbs
Weight
TECNICAL DATA
TECNICAL DATA
It is necessary to have
an exclusive tap for the
Washer water inlet .
The tap should be ¾ BSP
thread.
PREPARING THE WASHER FOR INSTALLATION
PREPARING THE WASHER FOR INSTALLATION
1. Remove the Washer from the
external packaging. Then
remove the internal
packaging piece and the
accessories bag which are
inside the Washer.
UNPACKING THE WASHER
3. Remove the plastic
protection from the
cabinet. Over time the
film will become more
difficult to remove, so
it is better to remove it
as you are installing
the washer.
Phases
Ground
Wire
120V
10A
A
A
A
B
C
C
D
D
A
B
C
D
tap
water outlet rubber hose
rubber hose for
water inlet
power
cord
Level the Washer
by turning its
rotary feet up or
down,until the surface
of casters is higher
than feet bottom
surface in order to
avoid vibrations.
C
W
D
2
2
ELECTRIC FEATURES
Voltage
Voltage
Range
Frequency
Eletric
current
Maximum
power
Max. power
consumpition
127V
220V
106 to 132V
198 to 242V
60 Hz
60 Hz
7,3 A
3,9 A
700 W
690 W
219 W/h
213 W/h
