background image

INSTALLATION INSTRUCTIONS

Commercial Dryer

Gas (120-Volt, 60-Hz) or  

Electric (120/240-Volt, 60-Hz)

www.whirlpoolcommerciallaundry.com

8563800D

TABLE OF CONTENTS

 

Page

Dryer Safety ......................................................................... 2

Tools & Parts ........................................................................ 5

Dimensions/Clearances  ......................................................  6

Location Requirements  .......................................................  8

Gas Dryer Electrical Requirements  ......................................  9

Gas Requirements  ............................................................  10

Electric Dryer Electrical Requirements  ..............................  11

Dryer Venting Requirements  .............................................  13

Gas Supply Connection  .....................................................  15

Installing Leveling Legs, Coin Slide, and Coin Box ...............  17

Electric Dryer Electrical Connections  .................................  18

Leveling  ............................................................................. 22

Complete Installation  ........................................................ 23

Changing to a 30- or 60-Minute Timing Cam  ...................... 24

Maintenance Instructions  .................................................. 25

If You Need Assistance  ....................................................... 25

Содержание Commercial Dryer





























Отзывы: