5019 301 10137
Whirlpool is a registered trademark of Whirlpool USA
Prewash might increase programme duration. Consumption values were measured in normalized conditions in compliance
with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the
water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
Add the detergent as described in the programme
table or in the chapter “Detergents and Additives” in
the booklet.
1. Turn the programme selector to the desired
programme.
2. The “Start/Pause” button is flashing.
3. Select the temperature by pressing “+” or “-”
button below the temperature display.
4. Select the spin speed by pressing the spin speed
button - the selected spin speed is indicated by
the indication next to it.
5. Select any desired option by pressing the option
button.
Selecting any option the indication lights up.
When the combination of options, temperature
and spin speed is not possible, the indication
lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
“Easy Ironing” button
• Can be used together with with Cotton,
Synthetics, Daily and Rapid Plus programmes to
make ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive Rinse” button
• More water and a longer time in rinse cycle is added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
CONSUMPTION DATA
Programme
Temperature
Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme
Duration
(hours : minutes)*
Cotton
95
4.5
49**
1.70
2:05
Cotton
60
5.0
46
0.95
2:20
Cotton
40
4.5
44
0.60
2:05
Synthetics
60
2.0
55
0.80
1:30
Synthetics
40
2.0
55
0.60
1:20
Daily
40
3.0
40
0.50
1:00
Rapid Plus
30
3.0
37
0.40
0:30
Delicates
30
1.5
60
0.50
0:45
Wool
30
1.0
60
0.30
0:40
Handwash
30
1.0
60
0.30
0:50
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Rinse Hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
• This option is particularly recommended for the
programme “Synthetics”, “Daily” and
“Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to “Rinse Hold” at
the time the “Rinse Hold” light in the programme
sequence indication is on.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the
programme will terminate automatically with
the final spin cycle for the present wash
programme.
• If you do not wish to spin the clothes, turn the
programme selector knob counter-clockwise to
the Drain programme and press the
“Start/Pause” button again when flashing. You
have to press “Start” button within 15 seconds
after reselecting the programme.
“Spin Speed Reduction” button
• Every programme has an automatic predefined
maximum spin speed.
• Press the button to set another spin speed.
• If the spin speed “0” is selected, the final
spinning is cancelled but intermediate spin peaks
remain during rinse. The water is drained out
only.
Open the tap and press the “Start/Pause” button.
The “Start/Pause” button lights up. The indicator
lamps show the sequence reached in the
programme. After starting the programme, the
sequence indication runs from left to right through
Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding lamp goes out.
The door can be opened when the “Door Open”
indication is on.
• All the lights of the programme sequence
indication are off.
1. Turn the programme selector to the “0” - “Off”
position.
2. Turn the water supply tap off.
3. Open the door and unload the machine.
4. Close the tap and leave the door ajar to allow
the drum to dry out.
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme (with
temperature), any options and another spin
speed if you want.
3. Press the “Start/Pause” button again.
The new programme continues at the same
position where the previous programme was
interrupted. Do not add detergent for this
programme.
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Set the programme selector to “Drain”.
The spin speed indicators show “0”.
3. Press the “Start/Pause” button to start the
drain programme.
PROGRAMME START
DOOR LOCK
PROGRAMME END
CHANGE THE PROGRAMME, OPTIONS
AFTER PROGRAMME START
CANCEL A PROGRAMME BEFORE THE END
