background image

6

D

C

H

hot

cold

B

A

Drain hose 

connection

C

IMPORTANT: THIS PROCEDURE MUST BE FOLLOWED TO
ASSURE PROPER INSTALLATION.

CLAMP

1/4" 
(0.64 cm)

A

B

C

D

H

G

E

F

To prevent the drain hose from coming off or leaking, it must be
installed per the following instructions.
• Wet the inside end of the drain hose 

(A)

with tap water. 

DO

NOT USE ANY OTHER LUBRICANT.

• Squeeze ears of one drain hose clamp 

(B) 

with pliers to open

and place clamp over the end of the drain hose.

• Open clamp and push end of drain hose onto drain connector

(C) 

until hose contacts ribbed stop 

(D)

.

• Place clamp over area marked “clamp”. Release clamp.

Standpipe or laundry tub drain system:

Open yellow clamp 

(E) 

and slide over “hook” end of drain hose

(F) 

to secure the rubber and corrugated sections together.

Floor drain system:

Do Not install “hook” end of drain hose to corrugated section.
Consult your plumber for proper installation.

Run water through both faucets into a bucket to get rid of
particles in the water lines that might clog hoses. Mark the hot
water faucet.

Put “hook” end of drain hose into laundry tub or standpipe.
Check for proper length of drain hose.

To prevent drain water from going back into washer:
• Do Not straighten “hook” end of drain and force excess drain

hose into standpipe.

• Do Not lay excess drain hose in bottom of laundry tub.

If drain hose does not fit into standpipe or is being
placed over the edge of a laundry tub, 

open other drain hose

clamp with pliers and place clamp over rubber end of drain hose

(G)

.

Insert end of hose extension 

(H) 

into rubber end of drain hose up

to stops on the sides of hose extension. Secure with clamp.

Inlet hose connection

(to faucets)

Attach bottom hose from the inlet marked "H" to hot water faucet

(A)

. Attach top hose from the inlet marked "C" to cold water

faucet 

(B)

. Tighten couplings to faucets by hand; then use pliers

to make additional two-thirds turn. 

Do Not overtighten;

this

could cause damage to couplings.

Inlets are plastic. Do Not strip or crossthread.

• 

(

A

)

• 

(

B

• 

(

C

(

D

• 

clamp

(

E

(

F

• 

• 

(

G

)

(

H

)

(

H

)

(

A

(

C

)

(

B

)

Содержание 8318507










Отзывы: