Water heater:
Set to deliver
140°F (60°C)
water to washer.
✔
Before you start...
Level floor:
Maximum slope
under entire
washer — 1 inch (2.5 cm).
1. Laundry tub or utility
sink drain system:
Needs a 20-gallon (76-litre) laundry
tub.
Important: Observe
all governing codes
and ordinances.
2. Floor drain system:
Location of washer:
✔
Check location
where washer will be installed. Make sure you have everything necessary
for correct installation. Proper installation is your responsibility.
Grounded electrical
outlet
is required
within 5 feet (152.4 cm)
of upper right corner of
washer cabinet. See
“Electrical requirements,”
Panel A.
The hot and cold water
inlets on the back of the
washer have 3/4 —
11-1/2 American hose
coupling standard
threads.
Hot and cold water faucets:
Should be within
3-1/2 feet (106.7 cm) of upper right hand corner of washer
cabinet (if not, see chart below). Provide water pressure
5-100 psi (34.5-689.6 kPa).
0"*
(0 cm)
0"*
(0 cm)
Front view
(door not shown)
Side view
Minimum installation spacing
Recessed area instructions
This washer may be installed in a recessed area or closet.
The installation dimensions
shown are the minimum
spaces allowable. Additional
spacing should be considered
for ease of installation and
servicing. If closet door is
installed, the minimum air
openings in top and bottom of
door are required. Louvered doors
with air openings in top and
bottom are acceptable. Companion
appliance spacing should be
considered.
closet door
Front view
closet door
17"
(43.2 cm)
14"
(35.6 cm)
max.
4"
(10.2 cm)
min.
1" (2.5 cm) min.
3" (7.6 cm)
3" (7.6 cm)
24 sq. in.
(155 sq. cm)
24 sq. in.
(155 sq. cm)
48 sq. in.
(310 sq. cm)
48 sq. in.
(310 sq. cm)
✔
Remove parts package. Untape and open washer lid. Remove literature package from washer.
Look at drain systems below to decide which system to use.
3. Standpipe drain system:
Needs a two-inch (5.1 cm) minimum diameter standpipe with minimum
carry-away capacity of 17 gallons (64 litres) per minute. A 2" (5.1 cm) dia. to
1" (2.5 cm) dia. standpipe adapter, Part No. 3363920, must be used with 1"
(2.5 cm) dia. drain systems.
Top of
standpipe
must be at
least 39
inches
(99.1 cm)
high and
no higher
than 72
inches
**
(182.8 cm)
from
bottom of
washer.
Floor standpipe
drain
Wall standpipe drain
Do Not store or
operate washer
below 32°F (0°C)
(some water
may remain in
washer).
See Use & Care
Guide for
“Winterizing”
information.
Top of tub must be
at least 34 inches
(86 cm) high and
no higher than
72 inches (182.8 cm)
from bottom of
washer.
You will need to buy:
nothing. If your installation is different,
see “Drain system” below.
2" (5.1 cm) dia. to 1" (2.5 cm) dia. standpipe adapter,
Part No. 3363920.
siphon break, Part No. 285320; additional drain hose, Part No.
3357090; and Connector Kit, Part No. 285442.
standard 20 gal. (76 litre), 34" (86 cm) high laundry tub or
utility sink, sump pump and connectors (available from local
plumbing suppliers).
nothing.
2 longer water inlet hoses: 6 ft. (182.9 cm) hoses, Part No. 76313
or 10 ft. (304.8 cm) hoses, Part No. 350008.
Top of
standpipe
must be at
least 39
inches
(99.1 cm)
high and
no higher
than 72
inches
**
(182.8 cm)
from
bottom of
washer.
Parts listed are available from your local dealer or authorized parts distributor.
If your home has:
39" (99.1 cm) high, 2" (5.1 cm)
dia. standpipe
1" (2.5 cm) dia. standpipe
floor drain
overhead sewer
standard 20 gal. (76 litre),
34" (86 cm) high laundry tub or
utility sink
water not close by
Drain system:
Requires a
siphon break,
Part No. 285320.
Siphon break
must be above
high-water level
in washer, at
least 28 inches
(71.1 cm) from
bottom of
washer.
Additional drain
hose will be
needed. See
chart above.
28"
(71.1 cm)
min.
Support:
Floor must be
sturdy enough to
support washer weight
(with water) of 315
pounds (143 kg).
**If the drain height is greater than 72 inches (182.8 cm), a sump pump system
must be used.
* Additional clearances for wall, door and floor moldings may be
required.
If a longer drain hose is needed,
use complete drain hose assembly [56 inches (142.2 cm) long], Part No. 661575, or drain hose [21 inches (53.3 cm) long], Part
No. 3357090, and Connector Kit, Part No. 285442. These kits are available from your local dealer or an authorized parts distributor.
Panel A
5"
(12.7 cm)
8"
(20.3 cm)
washer
drain
connector
To use drain hose
shipped with washer,
standpipe, laundry tub
or utility sink should be
within 46 inches
(116.8 cm) of the
washer drain connector.
34"
(86 cm)
34"
(86 cm)
