Page 5
5/16 - 18
Elastic Stop
Nut (2)
LOWER
BRACKET
UPPER
BRACKET
UPPER
BRACKET
5/16 Flat
Washer (2)
REAR DECK
In
st
al
l r
ub
be
r
l o
se
a
nt
o l
igh
tba
r h
ere
In
st
al
l r
ub
be
r
l o
se
a
nt
o l
igh
tba
r h
ere
In
st
al
l r
ub
be
r
l o
se
a
nt
o l
igh
tba
r h
ere
SEAL
Fig. 1
UPPER
BRACKET
REAR DECK
8 - 32 X 3/8"
Pan Head
Torx Screw (2)
8 - 32 X 3/8"
Pan Head
Torx Screw (2)
8 - 32 X 3/8"
Pan Head
Torx Screw (2)
5/16 - 18 X 4" Phillips
Round Head Machine
Screw (2)
5/16 - 18 X 4" Phillips
Round Head Machine
Screw (2)
5/16 - 18 X 4" Phillips
Round Head Machine
Screw (2)
Speaker
Cut-Out
Use second hole in,
from outer edge of lightbar
CHILD RESTRAINT TETHER
ADJUSTABLE BUCK
MOUNT BRACKET
LIGHTBAR
HOUSING
DECK
MOUNT
BRACKET
DECK
MOUNT
BRACKET
DECK
MOUNT
BRACKET
REAR
DECK
REAR
DECK
REAR
DECK
Installation 2017 Ford Taurus:
1.
Locate the rubber seal supplied with the mounting kit and install it onto the front edge of the lightbar which comes in contact with the
vehicle window.
On the rear deck (passenger side) locate the cap covering the child restraint strap holder. Snap the cover open to access
the bolt, then remove
the bolt and lift off the
cap.
2.
Locate the passenger
side adjustable buck
mount bracket and a
deck mount bracket
included
with
the
mounting kit.
NOTE:
Driver and passenger
side is indicated with
“D” or “P” at the end
of the serial number
stamped into bracket.
Secure the deck mount
bracket onto the strap
holder using the
1/4 -
20 X 3/4 inch Hex Head Machine Screw, 1/4 inch External Tooth
Lock Washer
and
1/4 inch Flat Washer
provided. and tighten
hardware firmly.
3.
Next, loosely secure the adjustable buck mount bracket to
the deck mount bracket using the supplied
1/4 - 20 X 5/8 inch
Phillips Pan Head Machine Screws, 1/4 inch External Tooth
Lock Washers
and
1/4 inch Flat Washer
.
4.
Repeat steps 1 - 3 for the Driver-side mounting bracket.
5.
Position the lightbar onto the rear deck and secure the lightbar to
the two buck mount brackets using the hardware shown.
6.
Hold the lightbar housing firmly against the glass as you tighten the
hardware securing the buck mount brackets to the deck mount
brackets. Make sure that the rubber window seal on the lightbar
housing fully engages the rear window. The lightbar should
maintain the seal against the windshield when the pressure is
released.
7.
Extend the wires to the control box and to power. It is
recommended you follow the vehicles wire harness when
extending the wires
(See Wiring)
.
Installation 2017-18 Chevy Impala:
1. Locate the rubber seal supplied with the mounting
kit and install it onto the front edge of the lightbar where it contacts the window.
2. Secure the upper mounting bracket to the lightbar with the supplied hardware
(Fig. 1).
3. Center the lightbar on the rear deck with the front edge of the
lightbar sitting securely against the window and make 2 holes
in the rear deck for the two 5/16 - 18 X 4” Phillips Round
Head Machine Screws.
4. Open the trunk and locate the speaker hole
(centered toward the inside of the trunk). The
retainer bracket will mount here.
5. Insert the two mounting screws into the
two holes you made in step 3. Line the
lower mounting bracket up with the
screws. The lower bracket will mount up against the
speaker hole as shown.
6. Make sure the rubber seal sits properly against the rear window
then tighten all mounting hardware firmly.
7. Extend the wires to the control box and to power.
(See Wiring)
.
INSIDE
TRUNK
REAR
DECK
R E A R
D E C K
MOUNT
ADJUSTABLE
BUCK MOUNT
#10 FLAT WASHER
10 - 32 X ½ INCH
PHILLIPS PAN HD
METAL SCREW
1/4 - 20 X 5/8 INCH
PHILLIPS PAN HD
MACHINE SCREW
1/4 - 20 X 3/4 INCH HEX HD MACHINE SCREW
#10 EXTERNAL TOOTH
LOCK WASHER
1/4” FLAT WASHER
1/4” FLAT WASHER
1/4 INCH EXTERNAL TOOTH LOCK WASHER
1/4 INCH EXTERNAL
TOOTH LOCK WASHER
LIGHTBAR
REAR
WINDOW
NOTE: The 2017 Inner Edge is shown here for example.
The 2018 Inner Edge will mount the same.
