Page 4
SA314
SIREN
SA314
SIREN
FIG. 1
W
H
E
E
L
W
E
L
L
W
H
E
E
L
W
E
L
L
W
H
E
E
L
W
E
L
L
Speaker attaches
to bracket as
shown here
Use the holes indicated
above for this application
Top view of bracket
Fig. 2
Fig. 2
Fig. 2A
Fig. 2A
Speaker attaches
to bracket as shown
Gravel Shield
FIG. 1
Air Conditioner
Condensor
Air Conditioner
Condensor
Air Conditioner
Condensor
Mounting
screws
Mounting
screws
Mounting
Screws
Front Bumper
FIG. 3
Use the holes
indicated for
this application
Top view of bracket
Rubbe
r Cover
Gravel
Shield
FIG. 2
5/16 - 18 X 1
Hex Head Bolt
(QTY 2)
OPTION - A
OPTION - B
5/16 Split
Lock Washer
(QTY 2)
5/16 - 18
Hex Nut ½" DIA.
(QTY 2)
14 X 3/4"
Hex Head
Screw (QTY 4)
Bracket can be mounted in several
positions. Always make sure the
wire exit faces down after mounting.
There are two mounting
options with this bracket.
Mounting hardware is
supplied for both:
Using the 1/4" self
tapping Hex Screws.
Using the 5/16 Hex bolt,
Flat washers, Lock Washer
and Hex Nut
Option "A"
Option "B"
5/16 Flat
Washer
(QTY 2)
1/4 X 1"
Hex Washer
Head Self
Tapping
Screw
(QTY 4)
MOUNTING HARDWARE LOCATION
A
A
A
A
B
B
driver failure and void the product warranty.
IMPORTANT: For drainage purposes, the speaker must
be oriented so the wire passage hole is in the
“6 o’clock” position. This is also the drain hole for the
speaker and must be located on the bottom for proper
drainage. Improper mounting will result in premature
SA316
BLACK: Negative (-)
WHITE: Positive (+)
Mounting: / 2002 - 2003 Ford Explorer:
The speaker will be located in front of the driver side front tire, behind the bumper. You will use two existing
nuts and their bolts that are already on the vehicle. Always be sure that the speaker wires exit the bottom after mounting for proper drainage.
1.
Secure the bracket to the speaker using the supplied mounting hardware (See hardware applications on page 2). An SA314 is shown in Fig. 1.
Refer to page 2 for the SA315. Be sure you mount the SA315 onto the bracket in the same position the SA314 is shown here.
2.
Looking in through the drivers side wheel well, find the 2 existing bolts on the vehicle that match up to the brackets mounting holes.
3.
Remove the 2 nuts from their bolts and mount the bracket (with speaker) securing it with the 2 nuts you removed (Figs. 2A & 2B).
4.
Extend the WHITE (+) and BLACK (-) speaker wires to your siren amplifier and connect as shown in the amplifier instructions.
Mounting: 2003 Suburban / Tahoe:
The siren will mount in front of the vehicles gravel shield, just forward of (and below) the air
conditioner condenser as shown (Figs. 2 & 3). Always be sure that the sirens wires exit the bottom of the siren after mounting for proper
drainage of the siren.
1.
Place the bracket onto the mounting surface and mark off the location of the mounting holes.
2.
Remove the bracket and drill the mounting holes an appropriate size for the supplied mounting hardware (See hardware applications on page 2).
3.
Secure the bracket to the speaker using the mounting hardware provided for your model speaker. An SA314 is shown. See page 2 for an SA315.
4.
Secure the bracket (with speaker) to the mounting location with the supplied mounting hardware.
5.
Extend the WHITE (+) and BLACK (-) speaker wires to your siren amplifier and connect as shown in the amplifiers instructions.
