Page 2
9 10
11
1
2
3
4
5
15.200" (Dual)
Pioneer™ Mounting Dimensions
9.280" (Single)
2.750"
All mounting
holes are
.343" dia.
2.750"
15
14
13
12
16
17
4
4
4
ITEM
PART NUMBER
DESCRIPTION
Pioneer Mounting Kit - Pierce Mount
B
F
racket, loodlight
Adjustable Mounting Bracket, Driver Side
Gasket
3/8 Flat Washer S.S.
5/16 Nylon Flat Washer
3/8 Split-Lok Washer S.S.
5/16 Split-Lok Washer S.S.
Bolt, 5/16-18 x 1", Hex Head S.S.
Soc. Button Head Screw, 3/8-16 X 1 1/2 S.S.
Screw, 1/4-20 X 1/4 Socket Set w/Cup Point
Adjustable Mounting Bracket, Pass.Side
0 1 - 0 4 8 6 1 2 1 - 0 0
0 7 - 2 4 3 7 3 5 - 0 0 0
0 7 - 2 8 6 1 2 1 - L 0 1
3 8 - 0 2 4 3 7 7 3 - 0 0
1 6 - 1 5 0 3 2 2 0 - 6 0
1 6 - 0 0 0 0 0 3 0 - 6 7
1 6 - 1 5 3 2 2 2 0 - 1 0
1 6 - 1 4 3 1 9 2 0 - 0 8
1 4 - 1 4 8 4 3 6 - 1 6 0
1 4 - 1 5 6 B 3 6 - 2 4 0
1 4 - 1 3 0 5 3 6 - 0 4 M
0 7 - 2 8 6 1 2 1 - R 0 1
QTY
4
1
2
2
1
4
4
4
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1
Cordgrip Pigtail
2 1 - 4 0 1 6 6 5 9 - 0 1
1
Seal
Locking Nut
1 6 - 0 0 1 7 9 9 2 - 0 0
1 3 - 1 5 S 1 4 0 - 1 7 6
1
1
01-0686136_ _ _
-00 = 12V / White
-01 = 12V / White (15')
-02 = 12V / Black (15')
-07 = 12V / Black
-24 = 24V / White
-27 = 24V / Black
D27= 24V / Desert Sand
Dual Pioneer-only
Dual Pioneer-only
Pioneer Plus-only
Sample Part Number Key
Pioneer Dimensions
8.18"
4.25"
Pioneer (Single)
4.25"
14.05"
Pioneer (Dual)
Cordgrip Installation
.670" dia.
Clearance
Hole
Pioneer
Cable
Sealing
Nut
Collet
Seal
Locking
Nut
MOUNTING
SURFACE
Cordgrip
Pigtail
.343 Dia.
Mounting Bracket
Gasket
5/16 Nylon Washer
Split-Lok Washer
5/16-18 x 1 Bolt
Mounting Surface
Mounting Information
Pioneer Mounting Bracket, Single
Pioneer Mounting Bracket, Dual
Screw, #10- 24 X 3/8 PFHMS, S.S.
0 7 - 2 4 3 9 0 1 - 0 0 1
0 7 - 2 6 B 8 5 4 - 0 0 1
1 4 - 1 0 4 11 6 - 0 6 0
PART NUMBER
DESCRIPTION
Pioneer™ Series LED Floodlight (Single)
Pioneer Series
LED Floodlight (Single)
PLUS
Pioneer
eries LED Floodlight (Dual)
S
Pioneer
eries
LED Floodlight (Dual)
S
PLUS
0 1 - 0 6 8 6 4 8 6 _ _ _
0 1 - 0 6 8 6 4 4 9 _ _ _
0 1 - 0 6 8 6 4 8 7 _ _ _
0 1 - 0 6 8 6 4 4 8 _ _ _
2.80"
6
7
8
Dual Pioneer Shown
For Reference Only
CAUTION-Hot Surface!
Make sure to route all wires
away from the heat sink fins.
Mounting...
1. Secure the appropriate Pioneer mounting bracket (Item #9 or
#10) to the Pioneer assembly with Item #11 (apply a drop of
LocTite® 242 to the threads). Insert the floodlight brackets (Item
#5) into the mounting bracket as shown. Secure these brackets
using the hardware provided (#12).
2. Using the appropriate hardware (Items #1, #2 & #3), install the
adjustable mounting brackets (Items #4 & #10) onto the
floodlight brackets.
3. Position the floodlight/mounting bracket assembly onto its
proposed mounting location. Make sure that the mounting
brackets fit properly onto the mounting surface.
4. When the best location has been determined, remove the
assembly from the mounting area. Using the mounting
dimensions shown below, carefully mark the areas where the
mounting holes are to be drilled. De-burr the holes after drilling.
5. The floodlight can now be mounted onto the vehicle using the
appropriate hardware (Items #14, #15, #16 & #17). Refer to the
“Mounting Information” illustration shown below. Be sure to
apply a drop of LocTite 242 to each of the four mounting bolts.
Using a torque wrench, tighten each bolt until a value of
between 10-12 ft/lbs. has been achieved.
Wiring...
All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125%
of the maximum operating current and FUSED at the battery
to carry that load. DO NOT USE CIRCUIT BREAKERS WITH
THIS PRODUCT!
Refer to the wiring guide included with your Pioneer for wire
functions, fuse values and optional switch connections.
IMPORTANT! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well
as all vehicle components/equipment.
