Page 2
#10-24 Elastic Stop Nut
#10 Flat washer
.631" Diameter X .060"
Disc Gasket
#10-24 X 5/8" LG SS
Carriage Bolt
End view of extrusion / Endcap removed
MOUNTING
SURFACE
#10 .631 DIA. X .060
FLAT WASHER
#10-24
ELASTIC
STOP NUT
DISK GASKET
BASE
EXTRUSION
POS 2 / BLACK
3 Amp
Fuse
10 Amp
Fuse
POS 1 / RED
POS 3 / WHITE
BATTERY: Negative
BACK LIGHT CONTROL: to +12VDC
source that is activated with the vehicles ignition switch
BATTERY: Positive
TACTLD1
REAR VIEW
1
2
4
5
6
3
7
10
8
11
9
12
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
IO
11
12
13
14
15
16
= BROWN
= RED
= N/C
= YELLOW
= GREEN
= N/C
= VIOLET
= GRAY
= WHITE-BROWN
= WHITE-RED
= N/C
= WHITE-YELLOW
= WHITE-GREEN
= N/C
= WHITE-VIOLET
= WHITE-GREY
DIP
SWITCH
CONTROL
12 POSITION
CONNECTOR
20
AMP
NOTE: For all information on programming and function refer to the control head instructions.
NOTE:
Switches fuses and fuse blocks are not supplied
1
1
1
1
1
1
1
1
1
1
= WHITE
2
3
4
5
6
7
8
9
IO
11
12
13
14
15
16
= WHITE
= WHITE
= WHITE
= WHITE
= WHITE
= WHITE
= WHITE
= WHITE-BROWN
= WHITE-RED
= WHITE-ORANGE
= WHITE-YELLOW
= WHITE-GREEN
= WHITE-BLUE
= WHITE-VIOLET
= WHITE-GREY
4
5
6
1
2
3
7
8
9
10
11
12
Lamp 3
Lamp 4
N/C
Lamp 1
Lamp 2
N/C
Lamp 5
Lamp 6
Batt. / Pos
N/C
N/C
Aux. Input
YELLOW
GREEN
BROWN
RED
VIOLET
GRAY
WHITE
N/C
N/C
WHT-BLU
INTERNAL CONNECTIONS TO LIGHTHEADS
TAM83_ _
FLASHER
FLASHER
TIR 1
TIR 2
TIR 3
TIR 4
TIR 5
TIR 6
BROWN (+)
WHITE-BROWN (-)
RED (+)
WHITE-RED (-)
RED (+)
BLACK (-)
GREY (SYNC)
RED (+)
BLACK (-)
GREY (SYNC)
YELLOW (+)
WHITE-YELLOW (-)
GREEN (+)
WHITE-GREEN (-)
VIOLET (+)
WHITE-VIOLET (-)
GREY (+)
WHITE-GREY (-)
Use SP/ST switch
fused at 3 Amps.
BLU - FLASHER (+)
ORG - FLASHER (+)
WHT/BLU - FLASHER (-)
WHT/ORG - FLASHER (-)
Installation:
Note: When routing the wires, it is important to choose a
path that will keep the wires away from excessive heat or
any vehicle equipment that could compromise the integrity
of the wires (ex. trunk lids, door jams, etc.).
WARNING! When the Traffic Advisor™ is mounted to the
rear of the vehicle, the cable exit must be on the passenger
side. If not, the flash pattern sequence you choose on the
control head will be incorrect. For example a left flashing
pattern will flash right.
1.
Position the unit in its proposed mounting location to ensure that it
fits properly. Draw a pencil line on the mounting surface using the
top and bottom of the extrusion as a guide.
2.
Two 1/4” holes are required to mount this unit. These holes may
be located anywhere along the horizontal centerline of the unit, but
must be centered between the upper and lower lines made in step
1.
Tip!
It’s a good idea to locate the mounting holes as far apart as
possible.
3.
Using a 1/4” drill bit, drill a hole in each of the areas scribed in the
previous step.
4.
Remove the end cap without the cable and insert the two carriage
bolts (included) into the extrusion as shown. Position these bolts
so they may pass through the mounting holes drilled in the
previous step.
5.
With the unit in position, place a gasket, flat washer and elastic
stop nut onto each bolt and tighten firmly.
Wiring:
WARNING! All customer supplied wires that connect to the
positive terminal of the battery must be sized to supply at least
125% of the maximum operating current and FUSED at the
battery to carry the load. DO NOT USE CIRCUIT BREAKERS
WITH THIS PRODUCT!
Extend the control wires to your switch panel and make the appropriate
connections using the wiring information below. The control head shown in
this manual is the TACTRLD1.
Note: If your system uses another control head, refer to your
control head manual for connection and operation.
IMPORTANT! Before returning this vehicle to active service,
visually confirm the proper operation of this product, as well as
all vehicle components/equipment.
