Page 2
10 X 1" PHILLIPS
PAN HD SHEET
METAL SCREW
(type A) (QTY 1)
#8-32 x 3/8 TORX HD
SCREW (QTY 2)
VISOR
SWIVEL
BRACKET
VISOR CLIP BRACKET
Fig. 2
SHEET METAL
HEADLINER
VISOR CLIP
MOUNTING
BRACKET
SHEET
METAL
ROOF
RUBBER
SEAL
Lightbar
Side View
WIND
SHIE
LD
Side View
DRIVER DOOR
Pry plastic
cover off
VISOR SWIVEL
BRACKET
WINDSHIELD
Remove screw
and visor clip
VISOR
CLIP
MOUNTING CLIP
(remove)
V
IS
O
R
Fig. 3
WINDSHIELD
Install Faston grommet
into existing hole in roof
that clip snapped into.
Fig. 4
Fig. 4
Re-install visor clip over bracket
using supplied #8 X 1" sheet metal screw
Install into Faston grommet using
supplied 1/4 X 1-1/4" PPHSMS
Install into Faston grommet using
supplied 1/4 X 1-1/4" PPHSMS
Install into Faston grommet using
supplied 1/4 X 1-1/4" PPHSMS
MOUNTING
B R A C K E T
Fig. 5
Fig. 5
IMPORTANT! The lightbar should be a minimum of 16" from radio antennas!
Installation / Standard:
1. Loosen (
do not remove
) the three screws securing the passenger-side
visor
swivel
bracket to the vehicle.
2. Remove screws securing vehicles
visor clip
and remove clip and hardware.
3. Secure mounting bracket to Inner Edge housing using hardware provided (Fig. 1).
4. Position the keyed opening of the mounting bracket directly under the location of
the
visor clip
removed in step 2 and remount the
visor clip
in its original location
using the original hardware (See Spacer installation in Fig. 1).
5. Firmly tighten any hardware loosened in this procedure.
6. Repeat this procedure for the driver-side assembly.
7. When rubber seal is in full contact with vehicle windshield and roof preventing
light output from entering passenger compartment tighten mounting hardware.
8. Route the lightbar cable down the vehicle A-pillar to your control head. Make all
wiring connections using the information in the wiring diagram.
Installation / Caprice:
1. Secure the mounting bracket to the Inner Edge housing using the two
#8 - 32 X
3/8
TORX
HEAD
SCREWS
provided (Fig. 2).
2. Loosen (
do not remove
) the
screws securing the passenger-side
visor
swivel
bracket
to the vehicle.
3. Slide the outside end of the mounting bracket under the
visor swivel bracket
(Fig.
2)
.
At the same time slip the rectangular hole in the other end of the mounting
bracket over the
visor clip bracket
. With the mounting bracket in position retighten
the
visor swivel bracket
hardware.
4. Using the screw hole in the mounting bracket as a guide, drill a pilot hole into the
sheet metal behind the headliner and secure other side of mounting bracket using
the supplied #10 X 1” PHILLIPS PAN HEAD SHEET METAL SCREW.
5. Repeat this procedure for the driver-side assembly.
6. The rubber seal should be in full contact with the windshield and the rear of the
lightbar should be in contact with the roof to prevent light from entering the
passenger compartment. When this has been achieved, tighten all mounting
hardware firmly to maintain contact (Fig. 2).
7. Route the lightbar cable down the vehicle A-pillar to your control head and make
all wiring connections using the information in the wiring diagram.
Installation 2013 Ford Fusion:
Figures 1 thru 3 show the driver side of the interior, looking up at the roof.
1. On the driver side
visor swivel bracket
, carefully pry the plastic cover off of the
front of the bracket (Fig. 3). The lightbar mounting bracket will sit in the space that
the cover occupied.
NOTE:
Pry the cover off using two flat blade screwdrivers
on each side to avoid braking the cover. The cover will not be used here but
should be saved in case you wish to remove the lightbar in the future.
2. Remove the
swivel bracket
mounting clip (located under the cover you removed in
step 1) and lift the swivel bracket assembly out. Install the supplied fastex
grommet into the hole in the roof sheet metal which the clip snapped into. Reinsert
the swivel bracket assembly (Figs. 3 & 4).
3. On the vehicle
visor clip,
remove the screw holding on the clip (The supplied #8 X
1" sheet metal screw will replace this screw) and remove the clip. (Figs. 3 & 4).
4. Secure the mounting bracket to the lightbar and position the bracket where it will
mount on the vehicle (Fig. 1 side view).
NOTE: The rubber seal should be in full
contact with the windshield and the rear of the lightbar should be in contact
with the roof to prevent light from entering the passenger compartment
5. Secure the lightbar bracket to the swivel mount using the supplied 1/4 X 1-1/4”
Phillips Pan Head Sheet Metal Screw. This screw will thread into the fastex
grommet you installed in step 2 and the bracket sits where the cover was (Fig. 6).
6. Line the rectangular hole in the other end of the lightbar bracket, up with the visor
clip and install the visor clip
over the lightbar bracket using
the supplied #8 X 1” Sheet
Metal Screw (Fig. 5).
7. Make
sure
all
mounting
hardware is tightened firmly
and repeat procedure for the
passenger side of the vehicle.
8. Extend the cables and connect
to power. Refer to the lightbar
manual for wiring and fusing
information.
Fig. 6
1/4 X 1-1/4"
PPHSMS
GROMMET
HEADLINER
VISOR SWIVEL
BRACKET
ROOF SHEET METAL
The Tahoe and Silverado have a retainer
which holds the headliner to the visor
clip that must be replaced
with the supplied spacer.
P
A
SSENGER
SIDE
Under
visor
swivel bracket
Under
visor
clip
Fig. 1
HEADLINER
VISOR CLIP
side view
VISOR CLIP
side view
VISOR CLIP
side view
SPACER
Explorer bracket
shown for example
Mounting
Bracket
ROOF
ROOF
#8-32 x 3/8 Torx
Hd Screw (2)
RU
BB
ER
SE
AL
Lightbar Side View
Lightbar Side View
WI
ND
SH
IEL
D
SPACER
HEADLINER
BRACKET