Wheelock SA-70 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 10

Wheelock SA-70 Скачать руководство пользователя страница 7

P81416 T

Sheet 7 of 10

Insert volume control shaft and set the volume approximately mid-way. (see Figure 13 and 14). As the system is put into service
readjust as necessary. If you want to prevent tampering of the control, simply pull out the volume control shaft. With the shaft
removed, volume can still be adjusted using a 5/64" hex drive. Shaft can be reinstalled later if necessary.

MOUNTING INFORMATION:

The SA-B4 is designed to mount on the surface of a wall. Remove the top cover by pushing the latch at the bottom of the housing
base with a small screwdriver, see Figure 14. Disconnect the speaker wires by unplugging them from the P.C. Board pins P1 (red)
and P2 (black). Figure 15 is the mounting template. Simply locate the template at the desired location and mount the base to the wall
with the screws provided. Connect wires as specified in "WIRING INFORMATION" on page 9, and then snap cover back onto base.
Be sure that the base sides line up between the cover sides and the 4 fingers on the cover sides, see Figure 16.

Figure 13.

SA-C8-A, SA-70, SA-90

Figure 14: SA-B4

Figure 15.

«
...
5
6
7
8
9
...
»

Содержание SA-70











Отзывы:

Нет отзывов