Wheel Horse 200 Series Скачать руководство пользователя страница 7

INSTRUMENTS  AND  CONTROLS 

200-SERIES  TRACTORS· 

11 

3 ·SPEED  MODEL S  

5·SPEED  MODELS 

11 

6·SPEED  MODEL S  

COMBINED .THROTTLE/CHOKE  CONTROL 

Combined  throttle/choke  control is located on  upper 

right  side  of  dash  panel.  To  start  engine  raise  lever 
all  the  way  up  past  detent  to  Choke  position.  To  op­

erate  tractor  raise  lever  to  detent  position  near  top  of 

slot.  lower  lever  before shutting engine  off.  If  engine 
is  warm  or  has  been  running,  raising  lever  to  Choke 

position  may  not  be  necessary  to  restart  it. 

2. 

INDICATOR  LIGHTS 

(211-5,211-6Models) 

Indicator  lights  are  located  on  upper  left  side  of 

dash  panel.  Test  switch  is  used  to  check  light  bulbs 

and  electrical  circuits.  Actuate  test switch to turn lights 
"On"  or  llFlashing"i  if  one  or  more  lights  are  out, 
check  wiring  and  replace  bulb  if  necessary  as  out� 
lined  in  "Maintenancell section  of  this  manual.  If  PTO 

Clutch  or  Clutch  Pedal  light  is  on  when  attempting  to 

start  engine,  check  that  control  is  in  proper  position 

for  starting.  All  lights  must  be  OFF  during  operation; 
if  lightCs)  is  on,  a  malfunction  is  indicated  in  that 
operation(s)  and  must  be  corrected. 

-3-

3. 

IGNITION SWITCH 

Ignition switch is  located on lower right side of dash 

panel  near  steering  column.  Ignition  switch  has  three 

positions  from  left  to  right, 

( 1 )  

Off, 

(2) 

Run, 

(3) 

Start. 

To  start  engine  turn  key  all  the  way  right  to  Start 
position.  Release  key  when  engine  starts  and  it  will 
automatically  return  to  Run  position.  When  switch  is 
turned  to  Off  position,  engine  stops  and  all  electrical 
accessories  are  turned  off. 

4.  VOLTMETER 

(211-6 Model) 

Voltmeter  is  located  on  dash  panel  to  left  side  of 

steering  column.  Voltmeter  is  a  gage  indicating  elec­
trical  system  battery  voltage. 

With  ignition  key  in  Off  position,  gage  is  not  ac� 

tuated.  When  ignition  key  is  turned  to  On  position, 
gage  should  read 

1 2  

Volts  or  slightly  above.  When 

starter  is  engaged,  gage  reading  should  not  drop 
below  8  Volts. 

After  engine  is  started  and  running,  gage  should 

read between 

1 2  

and 

1 6  

Volts.  If gage reads less  than 

1 2  

Volts  battery  is  discharging.  If  gage  reads 

1 6  

Volts  or  higher  for long periods of  time,  check  battery 
water  more  frequently. 

www.MyWheelHorse.com

Содержание 200 Series







































Отзывы: