background image

Specifications

MODEL 
POWER: PER CHANNEL (1% THD) 
Stereo Mode
8 Ohms 
4 Ohms 
2 Ohms 
Bridged Mono Mode: 
8 Ohms 
4 Ohms 
INPUT SENSITIVITY & IMPEDANCE
AT 4 Ohms 
UNBALANCED 1/4" Jack
BALANCED XLR 
VOLTAGE GAIN 
SLEW RATE: 8 ohms FULL SWING 
STEREO 

MP 1200 

 
260 Watts 
400 Watts 
640 Watts 
 
800 Watts 
1280 Watts 
 
0.775v 
10k Ohms 
20k Ohms 
35dB 
 
>30v/u sec 

MP 1800 

330 Watts 
600 Watts 
900 Watts 

1200 Watts 
1800 Watts 

0.775v 
10k Ohms 
20k Ohms 
36dB

>30v/u sec 

MP2800 

0.775v 
10k Ohms 
20k Ohms 
38dB 

>40v/u sec 
 

CHANNEL SEPARATION 
SIGNAL TO NOISE (20Hz-20kHz) 
DISTORTION (SMPTE-1M) 
FREQUENCY RESPONSE: 
 +/-1dB @ 4 Ohms
 +/-3dB @ 4 Ohms 
DAMPING FACTOR (8 ohms, 1kHz) 
TOPOLOGY 
CONNECTORS
INPUT 
OUTPUT 
 
CONTROLS
Front

Rear
INDICATORS

COOLING 
WEIGHT (GROSS) 
WEIGHT (NET) 
DIMENSIONS (H x W x D) mm 
DIMENSIONS (H x W x D) inches 

76dB 
100dB 
less than 0.05% 
 
20Hz to 20kHz 
5Hz to 50kHz 
Greater than 300 
Class AB 
 
XLR & 1/4" TRS 
5 WAY BINDING POSTS & 
SPEAKON OR SPEAKON

AC Switch, CH1 & 
CH2 gain knobs
Stereo/Bridge mode switch
Power switch on/off mute, 
Short circuit, 
Open circuit, Thermal
VARIABLE SPEED FAN 
23kg / 50.6lbs 
21.5kg / 47.3lbs 
133 x 483 x 355 
5.2 x 19 x 13.9 

76dB 
100dB 
less than 0.05% 

20Hz to 20kHz 
5Hz to 50kHz 
Greater than 300 
Class AB 

XLR & 1/4" TRS 
5 WAY BINDING POSTS & 
SPEAKON OR SPEAKON

AC Switch, CH1 & 
CH2 gain knobs
Stereo/Bridge mode switch
Power switch on/off mute, 
Short circuit, 
Open circuit, Thermal
VARIABLE SPEED FAN 
25kg / 55lbs 
23.5kg / 51.7lbs 
133 x 483 x 355
5.2 x 19 x 13.9 

78dB 
100dB 
less than 0.05%

20Hz to 20kHz 
5Hz to 50kHz 
Greater than 400 
Class H 

XLR & 1/4" TRS 
5 WAY BINDING POSTS & 
SPEAKON OR SPEAKON

AC Switch, CH1 & 
CH2 gain knobs
Stereo/Bridge mode switch
Power switch on/off mute, 
Short circuit, 
Open circuit, Thermal
VARIABLE SPEED FAN 
29.5kg / 65lbs 
28kg / 61.6 lbs 
133 x 483 x 355
5.2 x 19 x 13.9

Specifications and design subject to shange without notice for improvements.

Wharfedale 

website

:www.wharfedalepro.com

Wharfedale International Limited

Sovereign Court,Ermine Business Park, Huntingdon,

Cambs,PE296XU,England

 

1700 Watts
2700 Watts

600 Watts
950 Watts
1450 Watts

Содержание MP 2800









Отзывы: