Weston PRO 300 65-0401-W, Руководство пользователя

Страница: 10 / 10

BEFORE ATTEMPTING VACUUM PACKAGING BE SURE THAT THE
VACUUM SEALER IS SET UP IN ACCORDANCE WITH ALL OF THE SAFETY
PRECAUTIONS LISTED IN THIS BOOKLET.
1. With the Vacuum Sealer
plugged in and the power turned
on, check to be sure the
Auto
Mode Light is illuminated; press
the Mode Button until the auto light
is on (Figure 4).
2. Place the items to be vacuum
sealed into a vacuum bag. Allow at
least 2” (5 cm) at the open end of
the bag in order to create enough
seal space. Be sure not to cover
the Vacuum Port (Figure 5) .
3. Close the Clear Acrylic Vacuum Lid
and check that the bag opening is in the
center of the
Vacuum Chamber
(Figure 5).
4. Press and release the Start Button .
The 2-Piston Vacuum Pump will begin
removing air from the bag while the LED
Vacuum Window begins to count up. You
may need to apply light pressure to the Clear
Acrylic Vacuum Lid
during the count-up
process. The LED Vacuum Window will
count up starting at the number “1” and going
thru to the number “9”, before automatically
engaging the bag sealing process. (These
numbers represent stages, not seconds.)
5. Once the
LED Vacuum Window
displays the number “9”, the sealing process
will begin by counting down from the seal set time to “0” on the LED Seal Window .
6. Once the LED Seal Window has reached “0”, the Vacuum Sealer will
automatically stop the 2-Piston Vacuum Pump and release the vacuum pressure
moments later. DO NOT ATTEMPT TO PULL THE CLEAR ACRYLIC VACUUM
LID OPEN BEFORE THE VACUUM HAS BEEN RELEASED, SEVERE DAMAGE
TO THE SEALING BAR WILL RESULT.
Automatic
Mode Light
Mode
Button
AUTOMATIC MODE OPERATION
Figure 4
Leave 2”
Seal
Space
Vacuum
Ports
Bag in Center of
Vacuum Chamber
Figure 5
NOTE:
The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For
best results, only use the recommended vacuum bags with an embossed or mesh lining.
DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other
than the uses described in this booklet, could potentially damage the appliance and void
the warranty!
Manual
Mode Light
Manual Bag
Seal Button
MANUAL MODE OPERATION
Leave 2”
Seal
Space
Vacuum
Ports
Bag in Center of
Vacuum Chamber
Mode
Button
Figure 6
Figure 7
NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For
best results, only use the recommended vacuum bags with an embossed or mesh lining.
DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other
than the uses described in this booklet, could potentially damage the appliance and void
the warranty!
BEFORE ATTEMPTING VACUUM PACKAGING, BE SURE THAT THE
VACUUM SEALER IS SET UP IN ACCORDANCE WITH ALL OF THE SAFETY
PRECAUTIONS LISTED IN THIS BOOKLET.
1. With the Vacuum Sealer plugged
in and the power turned on, check to
be sure the Manual Mode Light is
illuminated; if not press the Mode Button
until the manual light is on (Figure 6).
2. Place the items to be vacuum sealed
into a vacuum bag. Allow at least 2” (5
cm) at the open end of the bag in order to
create enough seal space. Be sure not
to cover the Vacuum Ports (Figure 7).
3. Close the Clear Acrylic Vacuum Lid
and check that the bag opening is in the
center of the Vacuum Chamber (Figure 7).
4. While monitoring the vacuum bag, press
and release START Button . The 2-Piston
Vacuum Pump will begin removing air from
the bag. When the desired level of air has
been evacuated from the bag, press and
release the Manual Bag Seal Button . It
will start the sealing bag process.
Note: You may need to apply light pressure
to the Clear Acrylic Vacuum Lid during
this process.
Note: It requires some vacuum pressure in the bag to get good seal for the bag.
5. Once the LED Seal Window has reached “0”, the Vacuum Sealer will
automatically stop the 2-Piston Vacuum Pump and release the vacuum pressure
moments later. DO NOT ATTEMPT TO PULL THE CLEAR ACRYLIC VACUUM
LID OPEN BEFORE THE VACUUM HAS BEEN RELEASED, SEVERE DAMAGE
TO THE SEALING BAR WILL RESULT.
-10- -11-