-9-
-12-
NOTE:
The Tomato & Fruit Strainer Attachment cannot be used with meat products.
1. Hold the
Plastic Chute
with the outlet tilted almost fully downward and the head ring
facing the
Motor Unit
(figure 6).
2. Place the head ring over the round raised face on
the front of the
Motor Unit
. Position the tabs on the
head ring next to the slots in the corresponding tabs
extending from the round face (figure 7).
3. Rotate the
Plastic Chute
counterclockwise
until the tabs fit into the slots. The
Plastic Chute
should now be firmly held in place. When properly
positioned, the outlet of the
Plastic Chute
should
dip slightly downward.
4. Make sure the round end of the
Drive Shaft
is equipped with a metal washer, spring and metal
washer (in this order). Install the
Plastic Washer
onto the round end of the
Drive Shaft
(figure 8).
5. Insert the white end of the
Drive Shaft
into the
corresponding slot in the
Auger
.
6. Insert the
Auger/Drive Shaft
assembly into
the
Grinder Head
.
7. Position the
Screen
over the
Auger
. Line
up the tabs on the
Screen
with the notches in the
Grinder Head
. Hold the
Screen
in place.
Figure 6
Stainless
Steel
Screen
Plastic
Auger
Grinder
Head
Motor
Unit
Tray
Stomper
Head
Locking
Knob
Plastic
Chute
Drive
Shaft
USING THE STUFFER
NOTE:
Follow the “Food Safety Guidelines” in this
manual and as outlined by the U.S. Food and Drug
Administration (FDA) whenever using this appliance.
Keep meat/food refrigerated and covered. Do not
let meat/food sit out any longer than is necessary for
processing.
1. Place seasoned, ground meat in the
Tray
. Do
not overfill the
Tray
.
DO NOT
operate the
Grinder
without the
Tray
in place.
2. Twist or tie closed one end of the sausage
casing. You also can close and secure the end with
a hog ring.
3. Slide the open end of the casing onto the
Stuffing Funnel
until the entire casing is on the
Funnel
.
4. Make sure the
Motor Unit
is turned “off.” Connect the
Motor Unit
to an electrical outlet.
5. Turn the
Motor Unit
“on.”
6. Feed meat into the
Grinder Head
.
7. Use the
Stomper
to push meat into the
Grinder
.
NEVER use your fingers!
8. Hold the sausage casing onto the
Funnel
so that it does not slip off while stuffing.
9. Slowly release portions of the casing while stuffing to allow the casing to fill with meat.
10. When stuffing is complete, turn “off” the Motor Unit and disconnect it from the
electrical outlet.
11. Twist or tie closed each end of the casing. You also can close and secure the
ends with a hog ring.
HELPFUL HINT:
Firmly press ground meat into the
Grinder
with the
Stomper
to
release any trapped air.
TOMATO & FRUIT STRAINER
ASSEMBLY
Not included with all grinders.
Figure 7
Figure 8
Plastic
Chute
Round, raised face on
the front of Motor Unit
Tabs on
Motor Unit
Reverse
Button
Power
Switch
Outlet End
Head Ring
WARNING!
Before cleaning, assembling or disassembling the
Grinder
, make sure
it is turned “off” and disconnected from the power source. Test to make sure there is
no power to the
Grinder
by switching the
Motor Unit
“on” and “off.”
Follow all of the Safety Rules
and Warnings in this manual
whenever using this appliance.
Never leave this
appliance unattended.
Disconnect from power supply
when not in use.
WARNING!
Keep fingers, hands,
other body parts and
foreign objects away
from the inlet during
operation!
Only use the provided
stomper to push food into
the appliance.
Keep children away!
Bushing
Set
