14
15
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
The child safety device
This function prevents an accidental operation of
the appliance.
To activate the child safety device
• Activate the appliance with
. Do not set the
heat settings.
•
Touch
for 4 seconds (
button for models
WHI645BC & WHI945BC). The symbol comes on.
• Deactivate the appliance with
.
To deactivate the child safety device
• Activate the appliance with
. Do not set the
heat settings. Touch
for 4 seconds (
button for models WHI645BC & WHI945BC).
The symbol comes on.
• Deactivate the appliance with
.
To override the child safety device for only one
cooking time
• Activate the appliance with
. The symbol
comes on .
•
Touch
for 4 seconds (
button for models
WHI645BC & WHI945BC). Set the heat setting in 10
seconds. You can operate the appliance.
• When you deactivate the appliance with
,
the child safety device operates again.
Sense Boil® (This function only applies to
WHI645BC & WHI945BC)
The function automatically adjusts the temperature of
water so that It does not boil over once it reaches the
boiling point.
TIPS & INFORMATION
If there is any residual heat
on the
cooking zones you want to use, an acoustic signal
is emitted and the function does not start.
1. Touch
to activate the hob.
2. Touch
to activate the function.
A blinking appears for cooking zones on which you
can presently use the function.
3. Touch the control bar of any available cooking zone
for which you want to start the function (between the
heat setting 1-9).
The function starts.
If you do not choose any cooking zone within 5 seconds
the function does not activate.
TIPS & INFORMATION
Once the function starts the indicators above
the
symbol come on one after another until
the water reaches the boiling point
When the function detects the boiling point the hob
emits an acoustic signal and the heat level automatically
changes to 5.
If all cooking zones are already in use or there is some
residual heat on all of them, the hob emits a beep sound,
the indicators above
blink and the function does not
start.
To deactivate the function touch
(the function
deactivates and the heat setting goes down to 0) or
touch the control bar and adjust the heat setting manual
Hints & Tips for SenseBoil®
The function works best for boiling water and preparing
potatoes.
TIPS & INFORMATION
It does not work with cast iron and non-stick
cookware, e.g. with a ceramic coating. Enamelled
steel pots are recommended for achieving the best
results while boiling potatoes.
Check if the pot you chose is suitable for SenseBoil® by
monitoring the first cooking session.
To use SenseBoil® efficiently follow the advice below:
• FiIl between half to three quarters of the pot with cold
tap water leaving 4 cm from the rim of the pot empty.
Do not use less than 1 or more than 5 litres of water.
Make sure the total weight of the water ( or the water
and potatoes) ranges between 1-5 kg.
• If you want to cook potatoes, make sure they are
completely covered with water, but remember to leave
at least one quarter of the pot empty.
• To achieve the best results cook only whole, unpeeled,
medium-sized potatoes.
• Make sure you do not pack potatoes too tightly.
• Avoid producing external vibrations (e.g. from using
a blender or placing a mobile phone next to the
appliance) when the function is running.
• If you want to use salt, add it after the water reaches the
boiling point.
• The function may not work properly for water kettles
and espresso pots.
Hob²Hood
This is an advanced automatic function which connects
the hob to a special hood. Both the hob and the hood
have an infra-red signal communicator. Speed of the fan
is defined automatically on basis of mode setting and
temperature of the hottest cookware on the hob. You can
also operate the fan from the hob manually.
TIPS & INFORMATION
IMPORTANT
For most of the hoods the remote system is originally
deactivated. Activate it before you use the function. For
more information refer to hood user manual.
OPERATING INSTRUCTIONS (CONTINUED)
Operating the function automatically
The default automatic mode from the factory is H5. You can
change the automatic mode by following the instructions
below. When you activate the hob the hood will adjust the
fan speed automatically. Please note the below table is a
guide, the fan speed varies depending on the temperature
measured on the cooking zones of the cooktop which can
be affected by the heat setting(s) selected as well as the
size and volume of what you are cooking.
Automatic modes
AUTOMATIC
LIGHT
BOILING
FRYING
Mode H0
Off
Off
Off
Mode H1
On
Off
Off
Mode H2
On
Fan speed 1
Fan speed 1
Mode H3
On
Off
Fan speed 1
Mode H4
On
Fan speed 1
Fan speed 1
Mode H5
On
Fan speed 1
Fan speed 2
Mode H6
On
Fan speed
2
Fan speed 3
1. The hob detects the boiling process and activates fan
speed in accordance with automatic mode.
2. The hob detects the frying process and activates fan
speed in accordance with automatic mode.
3. This mode activates the fan and the light and does
not rely on the temperature.
Changing the automatic mode
1. Deactivate the appliance.
2.
Touch
for 3 seconds. The display comes on
and goes off
3. Touch
for 3 seconds.
4. Touch
a few times until comes on.
5. Touch
of the Timer to select an automatic mode
TIPS & INFORMATION
IMPORTANT
To operate the hood directly on the hood panel
deactivate the automatic mode of the function.
TIPS & INFORMATION
IMPORTANT
When you finish cooking and deactivate the hob,
the hood fan may still operate for a certain period of
time. After that time the system deactivates the fan
automatically and prevents you from accidental activation
of the fan for the next 30 seconds.
Operating the fan speed manually
You can also operate the function manually. To do
that touch when the hob is active. This deactivates
automatic operation of the function and allows you to
change the fan speed manually. When you press you
raise the fan speed by one. When you reach an intensive
level and press again you will set fan speed to 0 which
deactivates the hood fan. To start the fan again with fan
speed 1 touch .
TIPS & INFORMATION
IMPORTANT
To activate automatic operation of the function,
deactivate the hob and activate it again.
Activating the light
You can set the hob to activate the light automatically
whenever you activate the hob. To do so set the
automatic mode to H1 – H6.
TIPS & INFORMATION
IMPORTANT
The light on the hood deactivates 2 minutes after
deactivating the hob.
