manualshive.com logo in svg

Westinghouse WH4500, Руководство пользователя

Поделиться
Скачать
Westinghouse WH4500 Скачать руководство пользователя страница 23

24 

OPERATION

OTE:

N

If the engine fails to start after 5 seconds, 
release the engine control switch. Let the 
generator sit idle for 15 seconds and then 
repeat step 5. If the cranking speed drops after 
each unsuccessful attempt, then the battery 
may not be adequately charged. Manually 
start the generator as instructed in Manually 
Starting a Generator on page 21.

OTE:

N

The electric start generator is equipped with 
a battery charging feature. Once the engine 
is running, a small charge is supplied to the 
battery via the battery cables and will slowly 
recharge the battery. 

6.  As the engine starts and stabilizes, gradually move 

the choke lever back to the 

OFF

 position.

STOPPING THE GENERATOR

Normal Operation

During normal operation, use the following steps to stop 
your generator:

1.  Remove any connected loads from the control 

panel receptacles.

2.  Allow the generator to run at “no load” to reduce 

and stabilize engine and alternator temperatures.

3.  Push the engine control switch to the 

OFF

 position.

4.  Turn the fuel shutoff valve to the 

OFF

 position.

During an Emergency

If there is an emergency and the generator must be 
stopped quickly, push the engine control switch to the 

OFF

 position immediately. 

Содержание WH4500





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды