1
P.N.: 75-0115-RevA
ECO #: W14-0030
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service (800) 793-7846
www.westinautomotive.com
DATE: 04/15/2014
HDX RUNNING BOARDS
APPLICATION: FORD F150 2004-14 SUPER CAB/SUPER CREW
PART # 57-53315, 57-53525, 57-52365
INSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC.
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
.
ITEM
QUANTITY
DESCRIPTION
TOOLS NEEDED
1
1
RUNNING BOARD PASSENGER
13MM SOCKET
2
1
RUNNING BOARD DRIVER
13MM WRENCH
3
6
MOUNTING BRACKETS - 3 DRVR./3 PASS.
P# 57
-
53525 WILL HAVE QTY. OF 4 ONLY.
-
2 DRVR/2 PASS.
RATCHET
4
2
CENTER BRACKET 1 DRVR.-1 PASS.
THESE BRACKETS WILL BE IN P# 57
-
53525 KIT ONLY. FOR 09
-
14 F150 SUPER CREW.
RATCHET EXTENSION
5
2
BOOT SCRAPER
TORQUE WRENCH
6
36
M8 HEX HEAD BOLT
5/16” DRILL BIT
7
36
M8 24MM Flat Washer
TRANSFER PUNCH
8
36
M8 LOCK WASHER
SILICONE
9
24
M8 U-NUT
10
12
M8 16MM FLAT WASHER
11
12
M8 HEX NUT
12
4
M9.5 External Tooth Lock Washer
13
4
M9.5 Hex Head Self Tap Screw
2
1
3
4
1. Remove contents from box, verify if all parts listed are present and free from damage. Carefully read and understand all instructions
before attempting installation.
2. Identify driver and passenger side running boards
and install M8 u-nut clips (Item 9) to the underside of the boards.
Figure 1.
3. Starting on the drivers side rocker panel, locate a piece of black tape. Remove the tape to reveal a rectangle hole. Take (2) M8 nut clips
(item 9)
and place them over the two round holes located vertically into the rocker panel.
Figure 3.
4. Take the drivers side front mounting bracket (
item 3
), and attach it to the previously installed nut clips using (2) M8 hex head bolts (
item
6
), (2) M8 lock washers (
item 8
), and (2) M8 large flat washers (
item 7
).
Do not fully tighten at this time, the cradles will face the rear of
the vehicle
.
Figure 4.
5. Attach the mounting bracket to the bottom holes in the rocker panel using (2) M8 hex head bolts (
item 6
), (2) M8 large flat washers
(
item 7
), (2) M8 flat washers (
item 10
), (2) M8 lock washers (
item 8
), and (2) M8 hex nuts (
item 11
).
Do not fully tighten at this time
.
Figures 4 & 6.
6. Repeat steps 3-5 for the center and rear mounting brackets.
7. For
09-14 Super Crew p/n 57-53525
,
the center brackets will mount only using (1) M8 nut clip (
item 9
).
Figure 5.
8. Take the drivers side running board and place it onto the mounting bracket cradles; align the running board with the mounting holes in
the brackets and attach using (6) M8 hex head bolts (
item 6
), (6) M8 lock washers (
item 8
), and (6) M8 large flat washers (
item 7
)
Figure 2.
Do not fully tighten at this time
.
9. Align and adjust the running board as needed then fully tighten all hardware at this time. Torque all M8 hardware to 20 ft lbs.
10. Repeat steps 3-8 for the passenger side.
5
DRIVER
DRIVER
57
-
53525 ONLY
