Western MIDWEIGHT Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 24

Western MIDWEIGHT Скачать руководство пользователя страница 3

Lit. No. 64369, Rev. 04

3

June 15, 2010

SAFETY DEFINITIONS

NOTE: Indicates a situation or action that can lead
to damage to your snowplow and vehicle or other
property. Other useful information can also be
described.

CAUTION

Indicates a potentially hazardous situation
that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.

WARNING

Indicates a potentially hazardous situation
that, if not avoided, could result in death or
serious personal injury.

SAFETY

WARNING/CAUTION & INSTRUCTION
LABELS

Become familiar with and inform users about the
warning/caution labels on the back of the blade and
the instruction label on the headgear.

NOTE: If labels are missing or cannot be read, see
your sales outlet.

Instruction Label

Warning/Caution Label

LOWER BLADE WHEN VEHICLE IS PARKED.

DO NOT EXCEED GVWR OR GAWR INCLUDING BLADE
AND BALLAST.

REMOVE BLADE ASSEMBLY BEFORE PLACING
VEHICLE ON HOIST.

READ

OWNER'S MANUAL

BEFORE OPERATING OR

SERVICING SNOWPLOW.

TRANSPORT SPEED SHOULD NOT EXCEED 45 MPH.
FURTHER REDUCE SPEED UNDER ADVERSE TRAVEL
CONDITIONS.

PLOWING SPEED SHOULD NOT EXCEED 10 MPH.

SEE YOUR SALES OUTLET/WEB SITE FOR SPECIFIC
VEHICLE APPLICATION RECOMMENDATIONS.

59900

WARNING

CAUTION

«
1
2
3
4
5
...
»

Содержание MIDWEIGHT

























Отзывы:

Нет отзывов